Abstract:The paper shows the effect of solution temperature on the deposition rate of applying composite nickel-phosphorus coatings modified with boron nitride and polytetrafluoroethylene to powder samples made of improved P40, P40Kh and P40KhN steels obtained by hot stamping of porous sintered blanks. It has been experimentally established that within the range of 70–90 °C, the average deposition rate of modified BN and (C 2 F 4 ) n coatings is 15–19 μm/h, while the chemical composition of the improved steels and the surface configuration of the samples have no effect on the coating build-up rate. The mechanism of the formation of the structure and properties of nickel-phosphorus coatings (NiPC) without additives and those of NiPC modified with boron nitride and polytetrafluoroethylene during deposition, sintering and running-in is revealed. It has been established that immediately after deposition, Ni–P coating has an amorphous structure with inclusions of nickel particles, and its microhardness does not exceed 380–390 MPa with no modifiers added. In the dry friction mode at the running-in stage, Ni 12 P 5 and Ni 2 P phases are formed in the modified Ni–P coatings, allowing to improve their tribological properties, and in the steady-state mode, the phase disordering of the modified NiPC proceeds. It has been experimentally revealed that the coefficient of friction and wear decrease by 1.3 times when only (C 2 F 4 ) n is introduced into Ni–P coating, these indices decrease by 1.6 times when only BN is added, and they decrease almost twice when BN and (C 2 F 4 ) n are introduced together. It has been established that upon the combined (complex) modification of NiPC with BN and (C 2 F 4 ) n after the heat treatment, there is almost no nickel oxide phase, nickel boride of NiB type is formed in the coating during running-in, and its content does not decrease when entering the stationary friction mode, thus increasing tribotechnical properties of the coating. During running-in, the coefficient of friction of Ni–P + BN + (C 2 F 4 ) n coating decreases from 0.28 to 0.19, and the wear rate of such a coating in the stationary friction mode is 1.5 mg/h. The efficiency of applying the antifriction nickel-phosphorus coatings modified with BN + (C 2 F 4 ) n to the products made of the improved structural steels obtained by various methods has been theoretically and experimentally substantiated.

Wear behavior of graded nickel-phosphorus coatings with a medium phosphorus top layer: An experimental and molecular dynamics simulation study

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Friction and Wear Properties of Ni-P/Ti/DLC Multilayer Films

Microstructure, Friction and Wear Behavior and Corrosion Resistance of electroless Double-Layer Ni-P/Ni-Mo-P Coatings on AZ91D Magnesium Alloy

Microstructure and dry sliding wear evaluation of functionally graded coating deposited via atmospheric plasma spray

Tribological Behavior and Surface Analysis of Ni–P/BP Coatings

Effect of modifiers on the structure formation and properties of nickel-phosphorus coatings applied to powder steels

Molecular dynamics simulation of the nano-cutting mechanism of a high-phosphorus NiP coating

The Wear Resistance of an Ni-Cu-P Brush Plating Layer on Different Substrates

Tribological properties and wear mechanism of Ni@Gr reinforced Ni-based alloy coatings prepared via laser cladding

Effect of Surface Roughness and Structure Features on Tribological Properties of Electrodeposited Nanocrystalline Ni and Ni/Al2O3 Coatings

In-depth investigation of the evolution of microstructure and its influence on the mechanical properties of medium-phosphorus electroless nickel coatings after thermomechanical treatments

Microstructural Charactistics of Plasma Sprayed NiCrBSi Coatings and Their Wear and Corrosion Behaviors

Strengthening effect of α-ZrP nanosheet inclusions on corrosion resistance and wear resistance of Ni P deposits

Influence of MgAl layered double hydroxide nanosheets on the structure and properties of NiFeP composite coatings

Ni-P coatings electroplating - A review, Part I: Pure Ni-P alloy

Engineering Properties of Chromium Plating and Electroless and Electroplated Nickel

Tribological properties of Ni-BP/Ni coatings produced by electroless co-deposition

Improved microhardness and wear resistance of the as-deposited electroless Ni–P coating

A study of the wear resistance of carbon fiber composites deposited using an alkaline-based palladium-free electroless plating method

Mechanical properties of Ni-based coatings fabricated by electroless plating method