Abstract:Carbon fiber-reinforced polymers (CFRPs) are being used extensively in modern industries that require a high strength-to-weight ratio, such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymers, this comes at the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate the fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using the SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of the SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using a pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady-state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

A study of the wear resistance of carbon fiber composites deposited using an alkaline-based palladium-free electroless plating method

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Tribological properties of PEEK-based composite coating prepared by thermal spraying

Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating

Friction and Wear Behaviors of Surface-Modified Carbon Fabric/Epoxy Resin Composites

Friction and Wear of Electroless Ni-P-CS Composite Coating

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Testing and Analysis of Frictional Performance of Carbon Fiber/Metal Composite Materials

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

An Evaluation of the Wear Resistance of Electroplated Nickel Coatings Composited with 2,2,6,6-tetramethylpiperidine 1-oxyl-Oxidized Cellulose Nanofibers

Preparation and characterization of Ni-P-Al2O3-PTFE nanocomposite coatings by unidirectional jet electrodeposition

Friction and Wear Behavior of Electroless Wear-Resistant and Self-Lubricating Ni-P Composite Coatings

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Characterization and Wear Behaviors of Electrodeposited Ni-MoS2/SiC Composite Coating

Understanding friction and wear properties of carbon fiber/epoxy stitched composites

Tribological investigation into nickel-coated graphite polytetrafluoroethylene composites

Effect of graphene coating on modified and pristine carbon fibers on the tribological response of carbon fiber epoxy composites

Friction and Wear Behavior of Electroless Ni-Based Cnt Composite Coatings

Fabrication of in Situ Carbon Fiber/aluminum Composites Via Friction Stir Processing: Evaluation of Microstructural, Mechanical and Tribological Behaviors

Dry Friction and Wear Behavior of Laser-Sintered Graphite/Carbon Fiber/Polyamide 12 Composite