Experimental research on chemical desorption based on CO2-rich absorption solutions

Weifeng Zhang,Zhaoxiong Deng,Qiuhua Wang,Juan Li,Xuefei Qiu

DOI: https://doi.org/10.1016/j.ijggc.2021.103356

IF: 4.4

2021-07-01

International Journal of Greenhouse Gas Control

Abstract:<p>Although CO₂ capture by chemical absorption can achieve highly efficient removal of CO₂ from flue gas, the energy consumption of absorbent regeneration is high, and the CO₂ after desorption need to be compressed, transported and sequestrated. To reduce energy consumption and sequestrate CO₂ at low cost, an CO₂ desorption process was developed, in which the CO₂-rich solutions was regenerated and CO₂ was sequestrated in the form of CaCO₃. Five kinds of CO₂-rich solutions, monoethanolamine (MEA), methyldiethanolamine (MDEA), potassium glycinate (PG), MDEA/MEA and MDEA/PG were investigated by adding calcium hydroxide. The optimum reaction condition, which CO₂ loading was 0.621 mol/L and Ca(OH)₂ dosage was 1:1 for desorption of CO₂-rich solution, was determined. And the effects of three parameters (time, temperature and stirring rate) on CO₂ desorption rate were further analyzed. The optimum reaction temperature for the amine absorbents and the amino acid salt solvents were 20℃ and 50℃, respectively. The optimum reaction time and standing time were 30 min, respectively, and the optimum stirring rate was 800 r/min. MEA exhibited the highest desorption rate (85.31%) among the five solutions. In addition, the results of multicycle-cycle experiments showed that the MEA lean solution desorbed by chemical desorption still had excellent absorption capacity. Compared with the conventional thermal desorption process, the chemical desorption process had great advantages for CO₂-rich solutions regeneration and did not require further treatment of CO₂.</p>

energy & fuels,engineering, chemical, environmental,green & sustainable science & technology

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is: **Reduce the energy consumption in the CO₂ capture process through the chemical desorption process and achieve the low - cost mineralization and fixation of CO₂**.

Specifically, although traditional CO₂ capture methods (such as amine - based absorption methods) can efficiently remove CO₂ from flue gas, they have high energy consumption during the regeneration process, and the desorbed CO₂ also needs to be further compressed, transported and sequestered. In order to reduce energy consumption and cost, the author proposes a method based on chemical desorption, that is, by adding calcium hydroxide (Ca(OH)₂) to the CO₂ - rich solution, so that CO₂ precipitates in the form of calcium carbonate (CaCO₃), thereby achieving the mineralization and fixation of CO₂.

### Main research contents include:
1. **Optimization of reaction conditions**: The optimal CO₂ loading was determined to be 0.621 mol/L, and the optimal amount of Ca(OH)₂ was a Ca/C molar ratio of 1:1.
2. **Analysis of influencing factors**: The effects of reaction time, temperature and stirring rate on the CO₂ desorption rate were studied, and the optimal reaction temperatures were determined to be 20 °C (for amine - based absorbents) and 50 °C (for amino acid salt - based absorbents), and the optimal stirring rate was 800 r/min.
3. **Multi - cycle experiments**: It was verified that the lean solution after chemical desorption still has good absorption performance.
4. **Economic comparison**: Compared with the traditional thermal desorption process, the chemical desorption process has significant advantages in terms of energy consumption and operating conditions.

### Formula summary:
- CO₂ desorption rate calculation formula:
\[
\eta=\left(\frac{\text{Initial CO}_2\text{ rich loading}-\text{CO}_2\text{ rich loading at a certain time}}{\text{Initial CO}_2\text{ rich loading}}\right)\times100\%
\]
- Recirculating CO₂ loading calculation formula:
\[
\text{Recirculating CO}_2\text{ loading}=\text{CO}_2\text{ rich loading}-\text{CO}_2\text{ lean loading}
\]

Through these studies, the author hopes to provide an experimental basis for chemical desorption and CO₂ mineralization for industrial applications and demonstrate its advantages over traditional methods.