Abstract:High-temperature superconductor (Re)Ba2Cu3Ox (ReBCO) conductor on round core cable (CORC®) has a large current carrying capacity for high field magnets. Lorentz forces acting on CORC conductors, cause a reduction of the critical current, or even permanent degradation of their performance when exceeding critical values. Transverse compressive stress is one of the principal mechanical stresses when CORC cables are bundled to CICC conductors capable of operating at currents up to 100 kA in magnetic fields of up to 20 T. In this research, a mechanical-electromagnetic model is developed to study the effect of transverse compressive loads on the electromagnetic performance of CORC cables. A mechanical transverse load on the cable is implemented to simulate the electromagnetic force. A comparison of numerical simulations with experiments for a three-layer CORC cable is first performed to validate the model's reliability, with particular attention to critical current reduction during the transverse compression process. A novel feature of this paper is that the model developed can analyze both mechanical response under transverse compressive loads and electromagnetic performance under applied AC magnetic fields with low amplitudes. On this basis, the model investigates the effects of winding parameters on the axial strain and critical current reduction of the ReBCO layer in a single-layer CORC cable. The numerical analysis shows that increasing the winding angle can reduce the axial strain and critical current reduction of the ReBCO layer in the contact area. Subsequently, a detailed comparative study is carried out studying the axial strain of the ReBCO layer in the non-contact area with and without taking the winding core into account. In addition, a sudden increase of the magnetization loss is explained when the transverse compressive load reaches a certain level. Finally, a six-layer CORC cable's electromagnetic analysis is performed, and each tape layer's critical current reduction is investigated and discussed. The comparison of magnetization loss and current density between six- and single-layer CORC cables in the no-strain case is also given. This FE model can guide optimizing a cable design for specific application conditions.

Numerical analysis of delamination behavior in an impregnated HTS Roebel cable during cooling

Experimental and Numerical Study on the Magnetization Process of Roebel Cable Segments

Experimental and Numerical Simulations of ELM-like Transient Damage Behaviors to Different Grade Tungsten and Tungsten Alloys

Delamination behaviors of an epoxy-impregnated REBCO pancake coil during a quench

In Situ Detection of Delamination and Critical Current Degradation Caused by the Thermal Stress in Epoxy Impregnated REBa2Cu3O7−δ Coils

Critical current degradation and delamination crack observation of epoxy-coated REBCO superconducting tapes after thermal cycles in liquid nitrogen

Numerical Modeling of AC Loss in HTS Coated Conductors and Roebel Cable Using T-A Formulation and Comparison With H Formulation

Electromechanical degradation of REBCO coated conductor tapes under combined tension and torsion loading

Estimation of Self-Field Critical Current and Transport-Magnetization AC Losses of Roebel Cables

Performance study of REBCO multi-filament tapes/ CORC cables prepared by reel-to-reel mechanical incision

3D quench modeling based on T-A formulation for high temperature superconductor CORC cables

Numerical Investigation on Transverse Heat Transfer Properties in Cross Section of Full Size Nb3Sn CICC ITER Conductor

Current Sharing in Superconducting REBCO Cables-FEM Modeling

Research on the Radial Crimping Process for Stacked High-Temperature Superconducting Cable-in-Conduit Conductor

Mechanical behavior of HTS tape in highly flexible REBCO cable under tensile and torsional loads

Mechanical Properties of Concentric Three-Phase HTS Cable Based on Laminated Theory

Critical current characteristics and ampere force distribution of a novel HTS cable with different transposition lengths

Investigating the effect of transverse compressive loads on the electromagnetic performance of superconducting CORC® cables

Plastic Deformation Simulation of REBCO Tapes Using Particle Methods

Delamination Avoidance in Epoxy Wet-Wound REBCO Coils by Release Agent Coating

Electromagnetic-thermal-structure multi-layer nonlinear elastoplastic modelling study on epoxy-impregnated REBCO pancake coils in high-field magnets