Abstract:The nature of the interface between ceramic particle (CP) and metal matrix is critical to obtain solidification microstructures with optimal mechanical properties of CP-reinforced Al alloys in additive manufacturing. Generally, when the lattice misfit between the CP (e.g., TiB2) and the alpha-Al matrix is higher than 4%, the interfacial coherency reduces, lowering the effectiveness of CPs. Here, we demonstrate that an L12 three-dimensional compound (3DC), which possesses lattice misfit with alpha-Al lower than 1%, can be introduced in between TiB2 and alpha-Al via properly regulating the solidification cooling rate. In the 5TiB2/Al-4.5Mg-0.7Sc-0.2Zr (wt%) as a model system, the lattice coherence of the TiB2/alpha-Al interface is tailored by introducing a 10-30 nm thick Al3(Sc,Zr) 3DC interphase when the cooling rate is increased to-1000 degrees C/s. But, further increasing the cooling rate to-6800 degrees C/s, only Al3(Sc,Zr) two-dimensional compound (2DC) with an apparent lattice strain forms at the interface. Taking advantage of the cooling rate (102-103 oC/s) provided by laser direct energy deposition (L-DED), the low-misfit "TiB2/Al3(Sc,Zr) 3DC/alpha-Al" multi-structural interfaces are acquired, enabling the 3.56TiB2/Al-4.36Mg-0.72Sc-0.22Zr alloy as fabricated with L-DED to achieved improved strength-ductility synergy (yield strength 257 MPa, elongation 13.8%) due to the isotropically fine Al grain structure and the homogenous TiB2 particle dispersion. The outcome of this study provides fundamental knowledge on designing "ceramic/coherent primary interphase/metal matrix" multi-structural interfaces to improve the mechanical properties of engineering metallic materials manufactured by rapid solidification techniques, such as DED additive manufacturing (AM).

Programming Crystallographic Orientation in Additive‐Manufactured Beta‐Type Titanium Alloy (Adv. Sci. 28/2023)

Programming Crystallographic Orientation in Additive‐Manufactured Beta‐Type Titanium Alloy

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Anisotropic Mechanical and Microstructural Properties of a Ti-6Al-7Nb Alloy for Biomedical Applications Manufactured via Laser Powder Bed Fusion

Towards 3-D texture control in a β titanium alloy via laser powder bed fusion and its implications on mechanical properties

Controlling the microstructure and mechanical properties of a metastable β titanium alloy by selective laser melting

Mechanical Anisotropy of Laser Powder Bed Fusion Fabricated Ti-41Nb Alloy Using Pre-Alloyed Powder: Roles Played by Grain Morphology and Crystallographic Orientation

Laser Powder Bed Fusion of Beta-Type Titanium Alloys for Biomedical Application: A Review

Controlling lamellar orientation of Ti-47.5Al-5Nb-2.5V-1Cr alloy by conventional casting

Crystal Plasticity Finite Element Study of Incompatible Deformation Behavior in Two Phase Microstructure in Near Β Titanium Alloy

Experimental and Crystal Plasticity Finite Element Investigations of Plastic Anisotropy in Additively Manufactured Ti6Al4V Alloy

In-situ Twin-wire Additive Manufacturing: Integrated Fabrication of Refractory Medium Entropy Alloy, Correlation Between Orientation and Slip Systems Activation

A high-withdrawing-rate method to control the orientation of (?+?2) lamellar structure in a ?-solidifying ?-TiAl-based alloy

Effects of the crystallographic and spatial orientation of α lamellae on the anisotropic in-situ tensile behaviors of additive manufactured Ti–6Al–4V

Development of Bio-Compatible Beta Ti Alloy Powders for Additive Manufacturing for Application in Patient-Specific Orthopedic Implants

Columnar to Equiaxed Transition During Β Heat Treatment in a Near Β Alloy by Laser Additive Manufacture

Orientation effect on / phase interface mediated deformation mechanism in titanium alloy

Crystallographic Origin of Phase Transformation and Lamellar Orientation Control for TiAl-Based Alloys

Lamellar Orientation Control in Directionally Solidified Tial Intermetallics

Nanoscale Engineering of Low-Misfit TiB2/Al3(Sc,Zr)/α-Al Multi-Interface to Improve Strength-Ductility Synergy for Direct Energy Deposited Aluminum Alloy