Abstract:The grain-refining behaviors of 20Mn2 steel containing ZrC particles compressed with various degree of deformation (30%80%) at different temperature (8501150) were investigated by thermal simulating test.Microstructure analyses indicate that the role of ZrC particles as deformation nucleus and recrystallization nucleus enhances the nucleation rate of dynamic recrystallization of austenite and leads to grain refined with size of 34μm even when deformed at high temperature such as 1150 and 1050,further more that the ZrC particles as deformation nucleus increases concentrated degree of the located deformation in austenite makes deformation-induced ferrite transformation take place in advance at a higher temperature(950).Because a super-refined grain increases the critical cooling rate for obtaining martensite,the water-quenched microstructure deformed at the employed temperature developes from martensite to bainite and deformation-induced ferrite.Hardness analyses indicate that the hardening effect created by grain super-refining and strain is enough to offset the soft effect led by decrease in amount or even disappearance of martensite and bainite,also it can further increases the hardness of 20Mn2 steel to a higher value while the grain refining creates a bigger effect than the strain does.Analyses on the stress and strain in the deformation indicate that the austenite recrystallization causes a decrease in deformation resistance when deformed at 1150 and 1050,while deformation induced ferrite transformation plays the same role when deformed below 950.

Effects of yttrium on the microstructures, internal fraction and martensitic transformation in H13 die steel

The carbides, tensile properties, and work-hardening behavior of annealed H13 die steels with varied yttrium contents

The Influence of Warm Rolling Reduction on Microstructure Evolution, Tensile Deformation Mechanism and Mechanical Properties of an Fe-30Mn-4Si-2Al TRIP/TWIP Steel

Effect of Yttrium on Inclusion and Eutectic Carbide in D2 Cold Working Die Steel

Effects of rare-earth yttrium on crystallization and magnetic properties of Fe71 .4Si13B9.6Mo2Cr1Cu1P2nanocrystalline alloy

Microstructural Evolution and Mechanical Properties of 6cr13 Martensitic Stainless Steel Subjected to Cold Rolling and Heat Treatments

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Effect of Ti and rare earth on microsegregation and large-sized precipitates of H13 steel

Microstructure and Tempering Softening Mechanism of Modified H13 Steel with the Addition of Tungsten, Molybdenum, and Lowering of Chromium

Effect of Y on Martensitic Transformation and Mechanical Properties of NiMnSn High Temperature Shape Memory Alloy

Microstructure and High-Temperature Tensile Behavior of Modified H13 Steel with the Addition of Tungsten, Molybdenum, and Lowering of Chromium

Effect of Yttrium Addition on Microstructure and Mechanical Properties of Sr-Modified Low-Si Cast Aluminum Alloy

Effect of yttrium on phase composition and microstructure of FeCoNiAlCrB high entropy alloys

Microstructure and hot deformation behavior of the Cu-Sn-Ni-Zn-Ti(-Y) alloy

Determining role of heterogeneous microstructure in lowering yield ratio and enhancing impact toughness in high-strength low-alloy steel

Effect of the Combined Addition of Y and Ti on the Second Phase and Mechanical Properties of China Low-Activation Martensitic Steel

Effects of Deforming Temperature on Grain-refining of 20Mn2 Steel Containing ZrC Particles

Effect of Rare Earth Y on Microstructure and Mechanical Properties of High-Carbon Chromium Bearing Steel

Effects of yttrium additions on microstructures and mechanical properties of cast Al-Cu-Mg-Ag alloys

Heterogeneous nucleation of carbides attached to Y2O3 in Y-modified H13 steel

Effect of zirconium on inclusions and mechanical properties of China low activation martensitic steel