Abstract:The manifold microchannel heat sink shows great potential for cooling high-heat-flux electronic equipment owing to its exceptional thermal and flow performance. A new manifold ring-shaped channel design is introduced to improve the temperature uniformity for circular heat sources. A comparative analysis of the manifold straight channel, radial expansion channel and manifold ring-shaped channel designs is conducted based on the same heating area under equal mass flow conditions by numerical investigation using single-phase de-ionized water. The findings indicate that the newly proposed manifold ring-shaped channel design exhibits a lower maximum temperature, a lower average temperature, a better temperature uniformity and a smaller pressure drop in comparison to the straight channel and radial channel designs. Specifically, at a mass flow rate of 2.5 g/s, the ring-shaped channel design demonstrates a 71.4 % and 45.4 % reduction in the temperature difference between the maximum temperature and the minimum temperature of the heating surface, and the coefficient of performance is enhanced by 458.2 % and 169.7 % when compared to the straight channel and radial channel designs, respectively. Additionally, three improved designs based on the original manifold ring-shaped channel design are proposed to further enhance fluid flow distribution in the ring-shaped channel design. The results reveal that all three manifold ring-shaped channel optimizations further lower the maximum temperature, the average temperature and the temperature difference. Notably, the improved case3 exhibits the best thermal and hydraulic performances among all structures. When compared to straight channel and radial channel designs, the improved case3 demonstrates an 86.9 % and 75.0 % reduction in the temperature difference, and an increase of 201.2 % and 523.4 % in coefficient of performance under the equal mass flow comparison basis. A heat flux of 1200 W/cm2 can be dissipated at 6 g/s when the maximum temperature rise is kept below 60 K, with a pressure drop of 38 kPa.

Study on the flow and heat transfer performance of nanofluid in a novel manifold microchannel heat sink combining trapezoidal cross-section and curved corners

Nanofluids in microchannel heat sinks for efficient flow cooling of power electronic devices

Investigation on thermal performance of nanofluids in a microchannel with fan-shaped cavities and oval pin fins

Numerical Studies on the Hydraulic and Thermal Performances of Trapezoidal Microchannel Heat Sink

Micro Pin Fins with Topologically Optimized Configurations Enhance Flow Boiling Heat Transfer in Manifold Microchannel Heat Sinks

Property of Water-Nanoparticle Flow and Heat Transfer in the Double-Tube Heat Exchanger with Nanofluid

On the assessment of the thermal performance of microchannel heat sink with nanofluid

Numerical Study on a New Manifold Ring-Shaped Microchannel Structure for Circular Heat Source with Excellent Temperature Uniformity

Study of flow and heat transfer performance of nanofluids in curved microchannels with different curvatures

Secondary vortex drag reduction and heat transfer enhancement of nanofluids in hierarchical microchannels applied to thermal management of electronic components

Performance investigation of normal channel facile heat sink using hybrid nanofluid: an experimental and numerical approach

Numerical Study of Enhanced Heat Transfer of MicroChannel Heat Sink with Nanofluids

Comparative studies on heat transfer and flow resistance of nanofluid in microchannels with different sidewall micro-fins

Thermohydraulic performance of convergent and rectangular microchannels with rectangular grooves using silver nanofluid: numerical study

Numerical investigation of novel manifold microchannel heat sinks with countercurrent regions

Numerical simulation of convective heat transfer behavior of nanofluids in elliptical microchannels

Numerical study of different micro-channel structures on fluid flow and heat transfer performance

Heat transfer and flow characteristics of hybrid Al2O3/TiO2–water nanofluid in a minichannel heat sink

Comparison of cooling performance of nanofluid flows in mini/micro-channel stacked double-layer heat sink and single-layer micro-channel heat sink

Thermal performance improvement in water nanofluid/GNP–SDBS in novel design of double-layer microchannel heat sink with sinusoidal cavities and rectangular ribs

Flow thermohydraulic characterization of hierarchical-manifold microchannel heat sink with uniform flow distribution