Abstract:Digital light processing (DLP) 3D-printed Si3N4 ceramics, known for their exceptional performance, offer distinct advantages in meeting the high-strength and complex structural demands of industries such as aerospace, semiconductors, healthcare, automotive, energy, and machinery. However, due to Si3N4's strong chemical stability, low diffusion rate, low self-sintering ability, and high melting point, achieving densification under conventional sintering conditions is challenging. As a result, sintering additives are essential to promote the sintering process, lower the sintering temperature, improve densification, and enhance performance. In this study, 45 vol% Si3N4 slurries were prepared using DLP 3D printing technology, incorporating nine different combinations of sintering additives, including aluminum oxide (Al2O3), yttrium oxide (Y2O3), and aluminum nitride (AlN), in various ratios with Si3N4. The slurries were then sintered at 1800 °C for 2 h under a 1 MPa N2 atmosphere. Additionally, the phase composition, microstructure, grain distribution, and crack propagation of the materials. The results showed that a Si3N4 to Al2O3 and Y2O3 ratio of 95:2.5:2.5 produced elongated β-Si3N4 grain structures and enhanced density, achieving a maximum Vickers hardness of 12.88 ± 0.52 GPa. Additionally, the synergistic toughening effect of the rod-like β-Si3N4 grains and sintering aids significantly improved the fracture toughness of the Si3N4 ceramic matrix, with a flexural strength of 540.63 ± 10.05 MPa and a fracture toughness of 4.92 ± 0.07 MPa·m1/2. This study lays the foundation for the future application of 3D-printed Si3N4 ceramics, optimization of sintering aid combinations at different ratios, and performance enhancement in extreme environments.

Sintering behaviors and properties of porous ceramics derived from artificially cultured diatom frustules

Effect of Diatomite Additive on the Mechanical and Dielectric Properties of Porous SiO2-Si3N4 Composite Ceramics

Sintering Kinetics of Porous Ceramics from Natural Diatomite

Porous Silica Ceramics with Uniform Pores from the In-Situ Foaming Process of Silica Poly-Hollow Microspheres in Inert Atmosphere

Si3N4 Hollow Microsphere Toughened Porous Ceramics from Direct Coagulation Method Via Dispersant Reaction

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength

Microstructure and properties of porous Si 3 N 4 ceramics fabricated by digital light processing combined with spark plasma sintering

Fabrication and properties of diatomite ceramics with hierarchical pores based on direct stereolithography

Porous SiC Ceramics with Controllable Porosity Achieved by Micro-sized Powder through Recrystallization Sintering

Structure design influencing the mechanical performance of 3D printing porous ceramics

Effects of sintering temperature on properties of porous mullite/corundum ceramics

Fabrication and Properties of Porous Sic-Cordierite Ceramics

Effects of sintering temperature on properties of diatomite-based dental ceramic

A Simple and Efficient Way to Prepare Porous Mullite Matrix Ceramics Via Directly Sintering SiO2-Al2O3 Microspheres

Preparation And Properties Of High Strength Porous Si3n4 Ceramics

Sintering behavior and mechanical properties of sintered ceramics based on spodumene tailings

Mechanical and microstructural properties of cordierite-bonded porous SiC ceramics processed by infiltration technique using various pore formers

Fabrication and Characterization of Porous Cordierite Ceramics Prepared from Fly Ash and Natural Minerals

Microstructure and properties of highly porous Y2SiO5 ceramics produced by a new water-based freeze casting

Impact of Sintering Aid Type and Content on the Mechanical Properties of Digital Light Processing 3D-Printed Si3N4 Ceramics

Acicular porous mullite from diatom frustules