Abstract:Porous NiTi lattice structures are widely used in the manufacture of crucial components owing to their excellent shape memory effect, superelasticity, and high damping capacities. However, the specific strength and lightweight characteristics of porous NiTi lattice structures fabricated by conventional technologies are limited by unpredictability. In this work, three types of porous NiTi structures based on triply periodic minimal surface (TPMS) – Diamond, Gyroid, and Primitive – were designed and manufactured by the laser powder bed fusion (LPBF) additive manufacturing process . This work demonstrates LPBF is a feasible and efficient approach to fabricate highly accurate porous NiTi TPMS structures. Moreover, the influence of each of these structures on the mechanical and shape memory properties was investigated. Among the three structures, Gyroid had the smallest volume fraction deviation. Furthermore, the Diamond structure had the largest compressive modulus (782.82 MPa) and ultimate yield strength (163.14 MPa). The Gyroid and Primitive structures exhibit excellent elastic recovery deriving from high values of compressive modulus (662.44 MPa, and 703.29 MPa), and can maintain reliable structural robustness. The Primitive structure exhibited the lowest mechanical properties (37.80 MPa). During the cyclic compression test, Gyroid and Primitive show a smaller unrecovered strain than Diamond. Primitive shows the largest recovered strain during the heating process (6.98%). The higher mechanical flexibility of Primitive structure endows this structure with higher recovery ratio. During the direct compression test, the residual strain exhibits a positive correlation with the loading strain. All three structures exhibit good deformation recovery capability with a strain of 4%. At a strain of 12%, recovered strain during heating became the dominant factor in the recovery of the TPMS structure. Overall, porous NiTi TPMS structures are capable of reversible compressibility composed of rapid elastic recovery and controllable shape memory recovery. The unique performance of porous NiTi TPMS structure fabricated by LPBF renders it a highly efficiency energy-absorbing structure.

3D printing of TPMS structural ZnO ceramics with good mechanical properties

Preparation and thermal insulation properties of TPMS 3Y-TZP ceramics using DLP 3D printing technology

POLYMER-DERIVED SIC CERAMIC WITH TRIPLY PERIOD MINIMAL SURFACE STRUCTURE FABRICATION THROUGH DIGITAL LIGHT PROCESSING

Preparation and stereolithography 3D printing of ultralight and ultrastrong ZrOC porous ceramics

Preparation of excellent performance ZTA ceramics and complex shaped components using digital light processing 3D printing technology

3D printing of hollow lattice structures of ZrO2(3Y)/Al2O3 ceramics by vat photopolymerization: Process optimization, microstructure evolution and mechanical properties

3D Printing Magnesium-Doped Wollastonite/β-Tcp Bioceramics Scaffolds with High Strength and Adjustable Degradation

Effective thermal conductivity and heat transfer characteristics of a series of ceramic TPMS lattice structure

Enhancing mechanical properties and damage tolerance of additive manufactured ceramic TPMS lattices by hybrid design

Mechanical and shape-memory properties of TPMS with hybrid configurations and materials

Mechanical properties and failure analysis of 3D-printing micron-scale ceramic-based triply periodic minimal surface scaffolds under quasi-static-compression and low-speed impact loads

Investigation of permeability and biocompatibility of TPMS structures printed by laser powder bed fusion using Ti64-5Cu alloy for orthopedic implants

Mechanical properties of 3D printed interpenetrating phase composites with TPMS architectures

Digital Light Processing 3D‐Printed Porous Yttria‐Stabilized Zirconia with High‐Thermal Shock Resistance

Preparation of porous SnO2-based ceramics with lattice structure by DLP

Evaluation of Zirconia Ceramic Processed by Digital Light 3D Printing Applicated as Solid-Electrolyte Sensor

High temperature co-firing of 3D-printed Al ZnO/Al2O3 multi-material two-phase flow sensor

High temperature co-firing of 3D-printed Al-ZnO/Al<sub>2</sub>O<sub>3</sub> multi- material two-phase flow sensor

Mechanical and shape memory properties of NiTi triply periodic minimal surface structures fabricated by laser powder bed fusion

Properties and ceramic transformation of Si–Zr–O–C precursor ceramics with porous structure

Designing and additive manufacturing of biomimetic interpenetrating phase zirconia-resin composite dental restorations with TPMS structure