Abstract:A high-Cu-content-mixed solder paste comprising Sn–3.0Ag–0.5Cu (SAC305) + 20 wt% Sn– x Cu ( x = 3, 5, 8, and 10) was prepared in this study. The melting characteristics, wetting properties, liquid solder joint fluidity, melt viscosity, and surface tension of the mixed solder paste as well as the interfacial reaction mechanism and the shear properties of the mixed solder joints were investigated. The findings indicate that during the initial reflow, the solderability and wettability of the mixed solder paste are comparable to those of SAC305. However, during the second reflow, the overflow capability of the solder joint is restrained. Additionally, after the initial reflow, the mixed solder joint becomes a high Cu alloy, its composition deviates from the Sn–Ag–Cu eutectic point, and the liquidus temperature increases when remelted. For example, the liquidus temperature of SAC305 + 20 - wt% Sn–10Cu is 71 °C higher than that of SAC305 (225.7 °C) during the second heating. Furthermore, during the second reflow process, the increased liquidus temperature of the mixed solder joints leads to higher melt viscosity and surface tension. The surface tension of the SAC305 + 20 - wt% Sn–10Cu liquid alloy is 235.73 times that of SAC305, while the fluidity of the solder joints is restrained. In addition, a thin intermetallic compound (IMC) layer with larger grain is formed at the Cu/solder interface in the mixed solder joints. The thickness of the IMC layers at the Cu/solder interface in the mixed solder joints are as follows: 2.63 μm for SAC305 + 20 - wt% Sn–3Cu, 1.87 μm for SAC305 + 20 - wt% Sn–5Cu, 2.19 μm for SAC305 + 20 - wt% Sn–8Cu, and 2.21 μm for SAC305 + 20 - wt% Sn–10Cu. All of these values are lower than the thickness of the IMC layer in SAC305 (3.39 μm). In addition, we found that the addition of reinforced particles did not reduce the shear strength of the solder joints after multiple reflows. The shear strength of SAC305, SAC305 + 20 - wt% Sn–3Cu, SAC305 + 20 - wt% Sn–5Cu, SAC305 + 20 - wt% Sn–8Cu, and SAC305 + 20 - wt% Sn–10Cu were 43.04, 42.69, 43.10, 43.19, and 43.77 MPa, respectively, and all solder joints exhibited ductile fracture after shear tests.

Increasing shear strength of Au–Sn bonded joint through nano-grained interfacial reaction products

Formation of nano-phase Co3Fe7 intermetallic and its strengthening in Au80Sn20/CrMnFeCoNi solder interface

Sn-enhanced high-temperature reliability of Cu/Nano-Ag/Cu joint via transient-liquid-phase bonding

Ni mesh-reinforced ultrasonic-assisted Cu/Sn58Bi/Cu joint performance: Experiments and first-principles calculations

In-situ fusion process and Cu–Sn compounds evolution mechanism of nano-intermetallic compound mixed solder joints

The design of low-temperature solder alloys and the comparison of mechanical performance of solder joints on ENIG and ENEPIG interface

Interfacial Bonding Mechanism and Joint Weakness Area of Brazed SiC and Nb with AuNi Filler Alloy: First‐principles and Experimental Perspective

Microstructural evolution of Cu–Sn–Ni compounds in full intermetallic micro-joint and in situ micro-bending test

Study on the dual inhibition behavior of interfacial IMCs in Cu/SAC105/Cu joint by adopting SiC nanowires and nanocrystalline Cu substrate

Accelerated solid-liquid interdiffusion bonding of Cu joint using a Cu10Ni alloy mesh reinforced SAC305 composite solder

Significantly enhanced shear strength of Sn-Ag-Cu/Co-P ball grid array solder joints by CoSn<inf>3</inf> intermetallic compound

Effect of Nano-Cu 6 Sn 5 upon development mechanism of Cu–Ni–Sn compounds and mechanical characteristics for mixed solder joints

Effect of Various Parameters on the Shear Strength of Solid-State Nanoporous Cu Bonding in Cu–Cu Disks for Power Device Packaging

Intermetallic compound evolution and mechanical properties of Cu/Sn58Bi/Cu 3D structures blended with B 4 C nanoparticles during isothermal aging

Interfacial microstructure, shear strength and wettability of Ni-added Sn-0.3Ag-0.7Cu/Cu solder joint

Study on the evolution of interfacial (Cu,Ni)6Sn5 and shear property of (111)Cu/Sn/Ni micro joints under isothermal and TG-bonding

Microstructure, elastic modulus and shear strength of alumina (Al2O3) nanoparticles-doped tin–silver–copper (Sn–Ag–Cu) solders on copper (Cu) and gold/nickel (Au/Ni)-plated Cu substrates

Performance and interfacial reaction mechanism of nano-IMC-mixed solder paste with variable melting point

Microstructure evolution and grain refinement of ultrasonic-assisted soldering joint by using Ni foam reinforced Sn composite solder

Microstructure evolution and interfacial bonding mechanisms of ultrasonically soldered sapphire/Al dissimilar joints using Sn-based solders

Pulse electric current induced interfacial ductile phase on improving the mechanical properties of the Au20Sn/Cu solder joints