Abstract:Perovskite solar cells (PSCs) based on organometallic halide have received wide attention and been developed rapidly in recent years. However, the grain boundaries in perovskite film and defects in the interface in perovskite films dramatically degrade PSCs performance. Solvent annealing is an efficient method to fabricate high quality perovskite film with less grain boundaries. While most works carried out focused on the solvent annealing of perovskite films, we annealed PbI2 films in DMF, DMSO, acetone, and isopropanol (IPA) atmospheres and studied the effect of different atmospheres. We found that dense PbI2 was formed by annealing in DMF, acetone, and IPA atmospheres, which impeded the full reaction between PbI2 and CH3NH3I. Meanwhile, DMSO solvent annealing process led to porous PbI2 films, which facilitated the complete conversion of PbI2 to perovskite with larger grain sizes. As a result, Solar cells based on DMSO solvent annealing process exhibited the best efficiency of 18.5%, with a fill factor of 76.5%. We also annealed PbI2 in DMSO and CH3NH3PbI3 in ethanol for fabrication of pinhole-free CH3NH3PbI3 films on ZnO nanorods. Due to the suppression of carrier recombination by large grains, ZnO nanorods based PSCs with best efficiency of 17.3% was obtained. To suppress the interface defect, Li-doping compact TiO2 was also used as electron transport layer (ETL). Li doping reduced electron trap density and increased the conductivity of the ETL. As a result, the Li-doped compact TiO2 based planar heterojunction PSCs exhibit negligible hysteretic J-V behavior. Comparing with the undoped compact TiO2 based PSCs, the PCE of the Li-doped compact TiO2 film based PSCs is improved from 14.2% to 17.1%. Figure 1

Preliminary exploration of the influence of N+/NH+ ions/groups bombardment at TiO2 ETLs on performance of MAPbI3 perovskite solar cells

Constructing amorphous titanium nitride/titanium oxides hybrid electron transporting layer for achieving efficient and stable perovskite solar cells

Boosting the Performance of Perovskite Solar Cells through Systematic Investigation of the Annealing Effect of E-Beam Evaporated TiO2

Over 20% Efficiency in Methylammonium Lead Iodide Perovskite Solar Cells with Enhanced Stability Via "in Situ Solidification" of the TiO2 Compact Layer.

The Influence of the Thickness of Compact TiO2 Electron Transport Layer on the Performance of Planar CH3NH3PbI3 Perovskite Solar Cells

Optimizating TiO2 Electron Transport Layer for MAPbBr3 Perovskite Solar Cells by Way of Ga Doping

Effect of oxidized CdO quantum dots doped TiO2 electron transport layer on performance of mesoporous perovskite solar cells

Electrode Interfacial Layer Optimization of n-i-p Type Perovskite Solar Cells Based on a TiO2/Perovskite/P3HT Structure

(Invited) Improvement of Perovskite Films and the Perovskite/TiO2Interface

Energy Level Modulation of TiO2 Using Amino Trimethylene Phosphonic Acid for Efficient Perovskite Solar Cells with Average VOC of 1.19 V

Preparation of TiO2/SnO2 Electron Transport Layer for Performance Enhancement of All-Inorganic Perovskite Solar Cells Using Electron Beam Evaporation at Low Temperature

Theoretical investigation of the structural and electronic properties of Al-decorated TiO2/perovskite interfaces

Rationally reconstructing the surface microstructure of chemical bath deposited electron transport layer for efficient and stable perovskite solar cells

Room-temperature processed TiO2 to construct composite electron transport layers for efficient planar perovskite solar cells

Charge transfer enhancement of TiO2/perovskite interface in perovskite solar cells

Defect Passivation and Lithium Ion Coordination Via Hole Transporting Layer Modification for High Performance Inorganic Perovskite Solar Cells

Ti3C2 MXene nanosheets modified TiO2 ETLs enables efficient solar cells with outstanding device consistency

Interfacial Crosslinking for Efficient and Stable Planar TiO2 Perovskite Solar Cells

Designing Organic Electron Transport Materials for Stable and Efficient Performance of Perovskite Solar Cells: A Theoretical Study

In Situ Surface Fluorination of TiO 2 Nanocrystals Reinforces Interface Binding of Perovskite Layer for Highly Efficient Solar Cells with Dramatically Enhanced Ultraviolet‐Light Stability

Green Low-Temperature-solution-processed in Situ HI Modified TiO2/SnO2 Bilayer for Efficient and Stable Planar Perovskite Solar Cells Build at Ambient Air Conditions