Abstract:This paper presented an innovative three-dimensional vibration isolation bearing (3D-VIB) to mitigate horizontal seismic action and rail-induced vertical vibration. The 3D-VIB was composed of a thick laminated rubber bearing acting as the vertical vibration isolation module and a friction pendulum acting as the horizontal seismic isolation module. The thick laminated rubber bearing was used as a part of the slider in the friction pendulum. The compression performance of 3D-VIB was decoupled from its shear performance by concentrating the compressive deformation into the thick rubber bearing while shear deformation occurred independently in the friction pendulum module. The bearing capacity, vertical and horizontal properties of a full-scale 3D-VIB specimen were tested. In the test, the ultimate bearing capacity of 3D-VIB was 7 times that of the design compressive load of normal service condition. The vertical stiffness of the specimen under seismic vibration and vertical rail-induced vibration were tested separately. It was found that the vertical stiffness of the specimen under rail-induced vibration was 1.55 times higher than the vertical stiffness under seismic vibration. The horizontal performance of the 3D-VIB was characterized by stable parallelogram-shaped hysteretic curves similar to that of the traditional friction pendulum system. A user-defined element was developed and incorporated into ABAQUS to simulate the mechanical behavior of the 3D-VIB under different loading conditions, and simulation results agreed with the test results. The responses of a steel structure equipped with the 3D-VIB, while subjected to earthquake ground motions and rail-induced vibrations, respectively, were analyzed and compared with the non-isolated one. The analysis results suggested that with the installation of the 3D-VIB, the maximum inter-story drift ratio of the structure under maximum considered earthquake was reduced by about 88%. The average maximum transient vibration value of the rail-induced vertical vibration at the typical points of the conventional model was 86.2 dB, while that in the 3D-isolated model was 78.6 dB, the vibration reduction was 7.6 dB.

Seismic evaluation of isolation performance on single layer cylindrical reticulated shells supported along four sides

Shaking Table Study of the Three-Dimensional Isolation of a Cylindrical Reticulated Shell

Shaking table test of space double-layer cylindrical reticulated shell with three-dimensional isolation bearing

Analysis of dynamic characteristics and seismic response of single-layer folded-plane reticulated shells

Evaluation of isolation performance of, reticulated shell structures with curvature-consistent frictional pendulum isolation system through shaking table tests

Seismic protection of a single-layer spherical lattice shell structure using a separated three-dimensional isolation system

Experiment on Active Vibration Isolation of a Conical Shell Isolator

Seismic performance improvement of a three-dimensional isolated spherical reticulated shell structure using pseudo-negative-stiffness magnetorheological dampers

Seismic Analysis of Reticulated Shell Structure Based on Sensor Network for Smart Transportation Seismic Isolation Bearings

Shaking Table Tests on the Multi-Dimensional Seismic Response of Long-Span Grid Structure with Base-Isolation

Shaking table test of a novel Three-dimensional seismic isolation system with inclined rubber bearings

Shaking table test of a steel frame structure with layered three‐dimensional isolation

Experimental research and numerical simulation of a large-span isolated structure considering multi-dimensional input effects

Study on Column-Top Seismic Isolation of Single-Layer Latticed Domes

Mechanical Properties and Seismic Loss Assessment of Improved Isolation Bearing with Variable Stiffness

Pseudo-dynamic Experimental Study on Seismically Isolated Prefabricated RC Structure with Roller-Bearing Subjected to Mainshock-Aftershock Sequences

Vertical elastic dynamic impedance of a large diameter and thin-walled cylindrical shell type foundation

Development of an innovative three-dimensional vibration isolation bearing

Seismic Performance of Building with Novel Steel Roller Isolation Bearing: Experimental and Numerical Studies

Does seismic isolation reduce the seismic vulnerability and the variability of the inelastic seismic response? Large-scale experimental investigation

Seismic performance of advanced three-dimensional base-isolated nuclear structures in complex-layered sites