Promotion Effect of Ag on Syngas Transformation to Long-chain Alcohols over CuFe Catalysts

Zhiwei Qin,Yinwen Li,Meng Wang,Yanrui Su,Wa Gao,Ding Ma,Lin Yang

DOI: https://doi.org/10.1039/d4cc05510a

IF: 4.9

2024-01-01

Chemical Communications

Abstract:The catalyst CuFeAg0.5 derived from layered double hydroxide precursor exhibited highest STY toward long-chain alcohols of 0.139 g gcat-1 h-1. The introduction of Ag enhanced the interaction between Cu and...

What problem does this paper attempt to address?

The Effect of Na Promoter on Fe-Based Catalyst for CO2 Hydrogenation to Alkenes

Binglian Liang,Hongmin Duan,Ting Sun,Junguo Ma,Xin Liu,Jinghua Xu,Xiong Su,Yanqiang Huang,Tao Zhang

DOI: https://doi.org/10.1021/acssuschemeng.8b04538

IF: 8.4

2019-01-01

ACS Sustainable Chemistry & Engineering

Abstract:ABSTRACT: A series of Fe-based catalysts with accurately controlled amount of Na are synthesized to investigate the relationship between the promoter and the catalytic performance for CO2 hydrogenation to alkenes. With the increasing amount of Na, both CO2 conversion and alkenes selectivity increase at low and moderate amount and then plateau (with the highest to be 36.8% and 64.3%, respectively), while the corresponding methane production decreases to 7.2%. It is found that the addition of Na enhances the adsorption of CO2, facilitates the formation and stability of active species--Fe5C2, and inhibits the secondary hydrogenation of alkenes. All these effects lead to the desirable catalytic performance. Besides, it is observed that the content of Fe5C2 is related to the amount of Na. This study can provide scientific guidance to the design and the synthesis of high-efficiency catalysts for CO2 hydrogenation to high-value chemicals.
Effects of Ag Promotion for Co/Al2O3 Catalyst in Fischer-Tropsch Synthesis

Run Xu,Chaopeng Hou,Guofu Xia,Xia Sun,Mingfeng Li,Hong Nie,Dadong Li

DOI: https://doi.org/10.1016/j.cattod.2019.04.004

IF: 5.3

2020-01-01

Catalysis Today

Abstract:Ag promoted Co/Al2O3 Fischer-Tropsch synthesis catalysts were preparation by wetness impregnation and characterized by nitrogen physisorption, X-ray diffraction, temperature programmed technologies and H-2 chemisorption. Their performances of Fischer-Tropsch synthesis were evaluated in a fixed bed reactor. The result indicated that Ag promoter can improve the dispersion of the cobalt species and facilitate the reduction of CoO to metallic Co. Ag significantly increases the CO conversion rate and C-5(+) selectivity of Fischer-Tropsch reaction, while decreases the production of methane. However, negative effects were found at higher level Ag loading. As a result, the presence of relatively small quantities of Ag additive can help to enhance the performance of Co/Al2O3 catalysts in Fischer-Tropsch synthesis.
Interfacial Fe5C2-Cu catalysts toward low-pressure syngas conversion to long-chain alcohols

Yinwen Li,Wa Gao,Mi Peng,Junbo Zhang,Jialve Sun,Yao Xu,Song Hong,Xi Liu,Xingwu Liu,Min Wei,Bingsen Zhang,Ding Ma

DOI: https://doi.org/10.1038/s41467-019-13691-4

IF: 16.6

2020-01-03

Nature Communications

Abstract:Abstract Long-chain alcohols synthesis (LAS, C 5+ OH) from syngas provides a promising route for the conversion of coal/biomass/natural gas into high-value chemicals. Cu-Fe binary catalysts, with the merits of cost effectiveness and high CO conversion, have attracted considerable attention. Here we report a nano-construct of a Fe 5 C 2 -Cu interfacial catalyst derived from Cu 4 Fe 1 Mg 4 -layered double hydroxide (Cu 4 Fe 1 Mg 4 -LDH) precursor, i.e ., Fe 5 C 2 clusters (~2 nm) are immobilized onto the surface of Cu nanoparticles (~25 nm). The interfacial catalyst exhibits a CO conversion of 53.2%, a selectivity of 14.8 mol% and a space time yield of 0.101 g g cat −1 h −1 for long-chain alcohols, with a surprisingly benign reaction pressure of 1 MPa. This catalytic performance, to the best of our knowledge, is comparable to the optimal level of Cu-Fe catalysts operated at much higher pressure (normally above 3 MPa).

multidisciplinary sciences
Effect of Li Promoter on FeMn/CNTs for Light Olefins from Syngas

Qinyuan Chen,Weixin Qian,Haitao Zhang,Hongfang Ma,Qiwen Sun,Weiyong Ying

DOI: https://doi.org/10.1016/j.catcom.2019.03.010

IF: 3.51

2019-01-01

Catalysis Communications

Abstract:FeMnLi/CNTs catalysts with different Li content were prepared by the incipient wetness impregnation method for light olefins from syngas and investigated by N2 adsorption-desorption, XRD, H2-TPR, CO2-TPD and Mӧssbauer techniques. The addition of Li increased the surface basicity of catalysts and promoted the transformation of Fe3+ specious and formation of active phase, χ-Fe5C2, which was favorable to CO conversion and light olefins selectivity. The best catalytic performance was achieved over 8Fe8Mn1.5Li catalyst with CO conversion of 14.18% and light olefins selectivity of 48.42%.
Electron‐Deficient Cu Sites on Cu3Ag1 Catalyst Promoting CO2 Electroreduction to Alcohols

Ximeng Lv,Longmei Shang,Si Zhou,Si Li,Yuhang Wang,Zhiqiang Wang,Tsun-Kong Sham,Chen Peng,Gengfeng Zheng

DOI: https://doi.org/10.1002/aenm.202001987

IF: 27.8

2020-01-01

Advanced Energy Materials

Abstract:Copper-based catalysts electrochemically convert CO(2)into multicarbon molecules. However, the selectivity toward alcohol products has remained relatively low, due to the lack of catalysts favoring the adsorption of key intermediates in the alcohol pathways. Herein, a Cu(3)Ag(1)electrocatalyst is developed using galvanic replacement of an electrodeposited Cu matrix. The Cu(3)Ag(1)electrocatalyst enables a 63% Faradaic efficiency for CO2-to-alcohol production and an alcohol partial current density of -25 mA cm(-2)at -0.95 V versus reversible hydrogen electrode, corresponding to a 126-fold enhancement in selectivity and 25-fold increase in activity compared to the bare electrodeposited Cu matrix. Density functional theory calculations reveal that the interphase electron transfer from Cu to Ag generates electron-deficient Cu sites and favors the adsorption of CO(2)reduction intermediates in the alcohol pathway, such as CH3CHO* and CH3CH2O*. Thus, for this electron-deficient catalyst, the C2H5OH pathway is more preferable than the ethylene (C2H4) pathway, endowing the catalyst with an alcohol/ethylene ratio of 38:1. These findings suggest both experimental approaches and theoretical insights for exploring highly selective CO2-to-alcohol conversion.
Influence of Co Modified Mn/Cu/MgO Catalyst on the Synthesis of Mixed Alcohols from Syngas

Lanlei Wang,Jianwen Li,Yifei Che,Haitao Zhang,Weiyong Ying,Tao Li

2016-01-01

Abstract:Co modified Mn/Cu/MgO catalysts were prepared by co-precipitation method and were characterized by means of low-temperature nitrogen adsorption-desorption technique, X-ray diffraction(XRD), CO temperature-programmed desorption(CO-TPD), H2temperature-programmed reduce(H2-TPR), and X-ray photoelectron spectroscopy(XPS). The catalyst performance on the synthesis of mixed alcohols from syngas were investigated. The results indicated that Co2Mg and MnCo2O4 phase was formed, which facilitated the dispersion of the Cu, Mn and Mg species after adding the element of Co to Mn/Cu/MgO catalyst. Compared with the catalyst without Co, when the molar ratio of Co to Cu was 0.3, the selectivity ratio of C2+OH to C1OH and the space time yield of C2+OH increased from 0.31 to 3.12 and 9.07 g/(kg·h) to 28.83 g/(kg·h), respectively.The addition of promoter Co remarkably promoted the carbon insertion ability, which improved the selectivity of C2+OH in this reaction, and the catalyst showed high stability.
Impact of Cu complex anions on CuZnAl intercalated hydrotalcite-like catalysts for low-carbon alcohols synthesis from syngas

Shuyuan Wang,Zhe Hong,Lingling Yin,Zhihua Gao,Wei Huang

DOI: https://doi.org/10.1016/j.apcata.2024.119822

IF: 5.723

2024-05-29

Applied Catalysis A General

Abstract:Elucidating the structure-performance relationship of catalysts for low-carbon alcohols synthesis from syngas is crucial for designing efficient catalysts. In this study, CuO particle size, reducibility, and the number of oxygen vacancies could be adjusted by changing intercalated Cu complex anions, thereby affecting the catalyst's performance. The characterization results indicated that the insertion of [Cu(C 2 O 4 ) 2 ] 2- between ZnAl layered double hydroxide resulted in the largest CuO particles (26.5 nm), leading to an increase in the metallic copper surface area. Consequently, the highest CO conversion (13.0%) was achieved without altering alcohol distribution. On the other hand, when [Cu(EDTA)] 2- was inserted, the catalyst possessed the smallest CuO particle size (8.9 nm), more abundant oxygen vacancies, and enhanced interaction between Cu species and ZnO, which promoted carbon chain growth and resulted in a high C 2+ OH proportion of 75.8%. Our study thus provides a new perspective on catalyst structures for the syngas production of low-carbon alcohols.

chemistry, physical,environmental sciences
Catalytic conversion of syngas to mixed alcohols over CuFe-based catalysts derived from layered double hydroxides

Wa Gao,Yufei Zhao,Junmin Liu,Qianwen Huang,Shan He,Changming Li,Jingwen Zhao,Min Wei

DOI: https://doi.org/10.1039/c3cy00025g

2013-01-01

Abstract:A uniform and highly dispersed CuFe-based catalyst was obtained via a calcination–reduction process of a CuFeMg-layered double hydroxide (LDH) precursor, which exhibits good activity and selectivity towards catalytic conversion of syngas to mixed alcohols. X-ray diffraction (XRD) and scanning electron microscopy (SEM) reveal that the CuFeMg-LDH precursor possesses high crystallinity with a particle size of 40–60 nm. High resolution transmission electron microscopy (HRTEM) and scanning transmission electron microscopy (STEM) demonstrate a high dispersion of copper and iron species on the catalyst surface. The CuFe-based catalyst derived from CuFeMg-LDHs shows high CO conversion (56.89%) and the total alcohol yield (0.28 g mLcat.−1 h−1), as a result of the high dispersion of active species as well as the synergistic effect between the copper and the iron species revealed by X-ray photoelectron spectra (XPS) and H2 temperature-programmed reduction (H2-TPR) techniques. Therefore, this work provides a facile and effective method for the preparation of CuFe-based catalysts with high catalytic activity, which can be potentially used in syngas conversion to mixed alcohols.

chemistry, physical
Higher alcohols synthesis from syngas over P-promoted non-noble metal Cu-based catalyst

Yongjun Liu,Xuan Deng,Peide Han,Wei Huang

DOI: https://doi.org/10.1016/j.fuel.2017.07.043

IF: 7.4

2017-11-01

Fuel

Abstract:A series of P-promoted non-noble metal Cu-based catalysts without alkalis and Fischer-Tropsch elements were prepared by a complete liquid-phase method and tested for the synthesis of higher alcohols (C2+OH) from syngas in slurry bed reactor. The catalysts were characterized by XRD, 27Al-MAS-NMR, N2 adsorption, XPS, H2-TPR and NH3-TPD techniques. Results showed that the incorporation of an appropriate amount of phosphorus into the non-noble metal Cu-based catalyst could increase the surface Cu content, the amount of weak acid and improved the Cu+ reducibility, which promoted the synergistic effect between Cu and Al, and thus enhanced both stability and selectivity towards to higher alcohols formation. Activity results showed that the production of alcohols and hydrocarbons over this kind of catalyst followed A-S-F distributions, similar with conventional CuFe and CuCo based catalysts. The catalysts with Cu:Zn:Al:P=2:1:0.8:0.05 showed the best catalytic performance with long-term stability toward CO conversion and C2+OH selectivity (reaching 55%) during the lifetime test for 120h. It was speculated that AlOOH favored CO dissociation, and the synergism of Cu0, Cu+ and AlOOH was beneficial to the formation of higher alcohols. This work provided a new sight that alkalis and F-T elements were not indispensable for direct synthesis of higher alcohols from syngas over non-noble metal Cu-based catalysts.

energy & fuels,engineering, chemical
Tuning the Selectivity of Liquid Products of CO2RR by Cu-Ag Alloying

Yanzhi Xu,Changli Li,Yequan Xiao,Chenghui Wu,Yanming Li,Yanbo Li,Juguang Han,Qinghua Liu,Jingfu He

DOI: https://doi.org/10.1021/acsami.2c00593

IF: 9.5

2022-01-01

ACS Applied Materials & Interfaces

Abstract:The combination of Cu and Ag presents a promising way to steer the CO2 reduction products through regulating the surface active sites. However, the difficulty in forming the CuAg alloy with a controllable atomic ratio impedes the in-depth understanding of the structure-activity relationship of CuAg catalysts. Herein, we use E-beam evaporation to synthesize a series of CuAg films with uniform distribution and controllable stoichiometry to reveal the real reaction mechanism on CuAg for the electrochemical CO2 reduction process. Compared with Cu, the Cu1-xAgx (x = 0.05-0.2) alloy showed an apparent suppression of HCOOH and the ratio between C-2 liquid products (e.g., ethanol and acetate) and C-1 liquid product (HCOOH) is also increased. Operando synchrotron radiation Fourier transform infrared spectroscopy results suggest that the introduction of Ag into the Cu phase can significantly strengthen the absorbed *CO and *OCCO intermediates and suppress the O-C-O intermediates. This research provides a reliable way to inhibit the generation of HCOOH and enhance the production of liquid C-2 products during CO2RR and presents a guideline for the future manipulation of copper catalysts by alloying.
Tailored alcohol distribution by non-dissociated CO adsorption strength on engineered Cu sites in syngas conversion

Qi Ping,Yanru Zhu,Jian Zhang,Zhe An,Xin Shu,Hongyan Song,Jing He

DOI: https://doi.org/10.1016/j.jcat.2024.115873

IF: 7.3

2024-11-29

Journal of Catalysis

Abstract:The competition and diversity of coinstantaneous elementary reactions in syngas conversion make the production of targeted products with high selectivity much more challenging. This work demonstrates the control of product distribution in syngas conversion by changing the adsorption strength of non-dissociated CO on engineered Cu sites. The strength of non-dissociated CO adsorption has been tailored by atomic-Cu 1 or ensemble-Cu n on Co 1 Ga 1 intermetallic compounds. In syngas conversion, the introduction of either Cu sites could promote the selectivity of alcohols, while atomic-Cu 1 sites enhance the production of methanol and ensemble-Cu n sites favor the production of C 2+ alcohol. A strong adsorption of non-dissociated CO occurs on electron-deficient atomic-Cu 1 sites, leading to an increase of alcohols with > 90 % of methanol in alcohols due to direct hydrogenation. A weaker adsorption of non-dissociated CO occurs on ensemble-Cu n sites, which allows the carbonyl insertion to alkyl species, affording alcohols with ∼ 92 % of C 2+ alcohol.

chemistry, physical,engineering, chemical
Promoter Action of Ag on Cr-Ag/γ-Al2O3 Catalyst for CO Oxidation

Ping Chen,Bo Zhu,Yijun Zhong,Mengfei Luo,Shaohua Li,Hongli Wu

DOI: https://doi.org/10.3724/j.issn.1000-0518.1996.4.8991

1996-01-01

Abstract:A series ofγ-Al2O3-supported Cr-Ag bimetallic and individual mono-metallic catalysts was prepared by wetness impregnation method.The oxidation activity of CO was determined in a gas flow system. The effect of promoter Ag was studied by BET, XRD and TPR. The activity of Cr/γ-Al2O3 catalyst for CO oxidation was relatively poor. As the silver loading increased, the temperature of 100% coversion of CO over Ag/γ-Al2O3 catalysts decreased rapidly. The oxidation activity of catalyst was evidently enhanced by the addition of Ag, and increased with the content of Ag. The result of TPR showed that Ag could substantially change the reducibility of catalyst, TM decreased about 75℃,and the oxidation activity of catalyst was promoted.
Accelerating C2+ Alcohols Synthesis from Syngas by Simultaneous Optimizations of CO Dissociation and Chain Growth over CuCo Alloy Catalyst

Meiling Shui,Chao Huang,Peiyu Ma,Wenjie Li,Qun He,Wenlong Wu,Yisheng Tan,Jun Bao

DOI: https://doi.org/10.1016/j.cclet.2020.12.022

IF: 9.1

2020-01-01

Chinese Chemical Letters

Abstract:With regard to the reaction of higher alcohol synthesis (HAS), the optimizations of activity and selectivity towards C2+ alcohol are restricted by the improper equilibrium in two different CO activation pathways and chain growth capacity. Herein, we find that delibrately controlling the compositions of catalysts is an effective strategy to achieve the equilibrium of CO activation pathways and promote the chain growth. As a result, the optimized Cu0.25Co0.75 alloy catalyst can achieve a large proportion of higher alcohol in alcohol products (C2+OH/MeOH = 4.40), together with high CO conversion of 71.27% and space-time-yield of 147.65 g kg−1 h−1. The mechanistic studies suggest that the good performance of Cu0.25Co0.75 catalyst is attributed to the synergistic effect between alloyed Cu and Co.
Synthesis of mixed higher alcohols over Fe promoted Cu/ZrO2 catalysts by CO hydrogenation

Xiaoping Chen,Guisheng Wu,Yuhan Sun,Xiuzhi Wang,Bing Zhong

1999-01-01

Journal of Fuel Chemistry and Technology

Abstract:The effect of Fe on the catalytic performance of Cu-Mn-ZrO2 catalyst for CO hydrogenation was investigated. Fe was found to be an effective promoter for the synthesis of mixed higher alcohols, and the productivity of alcohols reached 0.14g ml-1h-1 with the selectivity for C2+ alcohols about 30w% (at T = 553K, P = 6.0MPa, GHSV = 3000h-1). A mixture with comparable amount of linear alcohols and iso-butanol was produced, the increase of temperature leaded predominant alcohol products changed from linear species to iso-butanol. It was thought that the products distribution was determined by two kinds of mechanisms, and the synergistic effect in catalysts led to the production of considerable amount of iso-butanol at moderate reaction conditions. No obvious amount of higher hydrocarbons was observed. The further modification by potassium was found to enhance C2+ alcohols selectivity, and suppress the formation of methane effectively, but the formation of CO2 increased obviously.
Study of Cu-Fe-Co-M/SiO2 (M = Unpromoted, Li, Na, K and Cs) Catalysts for Mixed Alcohols Synthesis from CO Hydrogenation

hai jun guo,lian xiong,cai rong luo,jie li,fei ding,xin de chen,yong chen

DOI: https://doi.org/10.4028/www.scientific.net/AMR.347-353.3691

2012-01-01

Abstract:A series of Cu-Fe-Co based catalysts prepared by co-impregnation method using different alkali additives was characterized by BET, XRD and FESEM-EDX and investigated under MAS from CO hydrogenation. The results showed that the catalyst Cu25Fe22Co3-Na-3/SiO2 has the highest catalytic activity and selectivity of total alcohol and C5+OH. XRD and FESEM-EDX demonstrated the Na-3 catalyst exhibited homogeneous distribution of elements and effective synergy effect between Cu and Fe components, thereby performed good catalytic performances for MAS from CO hydrogenation. The presence of a suitable content of alkali promoter was necessary for mixed alcohols synthesis from syngas.
Application of Cu-Fe based catalysts in synthesis of low carbon mixed alcohols from syngas

Su Yanmi

Abstract:The synthesis of low carbon mixed alcohols from syngas with high performance catalysts provides a new use pattern of syngas.The catalyst plays an important part in synthetic reaction.Introduce modified methanol catalysts,modified Fischer-Tropsch catalysts and rhodium-based catalysts.As one of the modified Fischer-Tropsch catalysts,Cu-Fe based catalysts are widely used for low cost,mild reaction condition,high activity and great alcohol and C2+OH selectivity.Introduce the function mechanism of Cu-Fe based catalysts,and the influence of main components,promoters,carriers and preparation methods on their performance.

Engineering,Chemistry
Enhanced CO2-to-CH4 Conversion Via Grain Boundary Oxidation Effect in CuAg Systems

Lei Wang,Xue Yao,Yi Xiao,Cheng Du,Xiyang Wang,Dmitry Akhmetzyanov,Zuolong Chen,Youchao Teng,Tao Guo,Yongzan Zhou,Joel P. Mills,Ning Chen,Weifeng Chen,Brant Billinghurst,Khaled M. Ibrahim,Jamie H. Warner,Chandra Veer Singh,Zhongchao Tan,Samira Siahrostami,Yimin A. Wu

DOI: https://doi.org/10.1016/j.cej.2024.156728

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:The authentic active sites of oxide-derived copper (OD-Cu), namely grain boundaries (GBs) and oxidized Cu delta+ species, is still debatable, and their role in governing CH4 conversion remains unclear. Herein, this study answers these questions using bimetallic catalysts by novel electro-shock strategy with controllable GBs for the oxidization of Cu delta+ species by modulating Ag loading. The Ag enrichment at the GBs facilitates the bonding of oxygen with the uncoordinated Cu atoms, resulting in GB oxidation effect. The obtained CH4 selectivity is twice that of GBs or nanoalloy effect. The enhanced performance is attributed to the stable Cu delta+ species and unique electron transfer mechanism from GB oxidation structure. Operando attenuated-total-reflection Fourier-transform-infrared-spectroscopy unveils the reaction pathway of CO2-to-CH4 and the sluggish reversible quenching processes of intermediates. Theoretical calculations indicate that the weak *CO adsorption on GB oxidation structure facilitates *CO hydrogenation, promoting CO2-to-CH4 conversion.
Effect of zinc source on the ethanol synthesis from syngas over a slurry CuZnAl catalyst

Jing Liu,Yongjun Liu,Wenjun Yan,Denghui Yang,Jinchuan Fan,Wei Huang

DOI: https://doi.org/10.1016/j.ijhydene.2020.06.166

IF: 7.2

2020-09-01

International Journal of Hydrogen Energy

Abstract:Three CuZnAl catalysts were prepared with three kinds of zinc sources including zinc nitrate, zinc oxide, zinc carbonate by a complete liquid method, their catalytic performances were investigated and the structures were characterized by XRD, BET, TPR, NH3-TPD, FT-IR, TEM and XPS. The results show that three catalysts own the ability to direct production of ethanol and higher alcohols from syngas, which occur at not any additives. It is found that a stronger electron transfer from Zn to Cu and Al occurred more in CAT-T and CAT-X, prepared with zinc carbonate and zinc nitrate, than CAT-Y with zinc oxide, which can cause the reduction of ZnO in part, producing oxygen deficiency species Zn(2−δ) that are associated with the ability of growing carbon chain. CAT-Y shows a comprehensive advantage.

energy & fuels,electrochemistry,chemistry, physical
Influence of Manganese Promoter on Co-Precipitated Fe–Cu Based Catalysts for Higher Alcohols Synthesis

Mingyue Ding,Minghuang Qiu,Jianguo Liu,Yuping Li,Tiejun Wang,Longlong Ma,Chuangzhi Wu

DOI: https://doi.org/10.1016/j.fuel.2012.06.034

IF: 7.4

2013-01-01

Fuel

Abstract:Effect of manganese promoter on the microstructures of co-precipitated Fe-Cu catalysts was investigated by N-2 physisorption, X-ray diffraction (XRD), and temperature-programmed reduction/desorption of hydrogen (H-2-TPR/TPD). Higher alcohols synthesis (HAS) was performed in a fixed bed reactor. The characterization results indicated that incorporation of manganese into the Fe-Cu based catalysts facilitated the formation of Fe-Mn-O solid solution and promoted the dispersion of both the iron and copper species. In the HAS reaction, the catalytic activity of CO hydrogenation, selectivity of C-2(+) OH and hydrocarbons increased gradually with increasing Mn concentration, which may be attributed to the well dispersion of both the iron and copper surface active sites in higher manganese content. The optimum conditions for producing higher alcohols from syngas were determined as 270 degrees C and 6.0 MPa. Crown Copyright (C) 2012 Published by Elsevier Ltd. All rights reserved.
The effect of CuO crystallite size on the structure and performance of CuZnAl catalyst for mixed alcohols synthesis from syngas

Jingrong Wang,Zhihua Gao,Pengquan Yan,Yaxing Shen,Rui Yang,Zhijun Zuo,Wei Huang

DOI: https://doi.org/10.1016/j.jpcs.2022.110883

IF: 4.383

2022-07-13

Journal of Physics and Chemistry of Solids

Abstract:CuO with a large microcrystalline differentiation was prepared by hydrothermal method, and the activity of the CuZnAl catalysts prepared by combining CuO with ZnAl has been tested in the CO hydrogenation reaction. The effect of Cu species crystallite size on catalytic structure and performance was revealed. The experimental results show that CuO crystallite grow with the raising of hydrothermal temperature. When the hydrothermal temperature was 130 °C, CZA-130 exhibited the stable crystallite size of Cu species, high Cu/Zn molar ratio, and strong interaction between copper and zinc oxide, so the selectivity of total alcohol could reach up to 71.39%. Moreover, the ratio of C 2+ OH in the alcohol product is positively correlated with higher ratio of Cu + /Cu 0 and total number of alkalis, which are related to the ability of growing carbon chain.

physics, condensed matter,chemistry, multidisciplinary

Promotion Effect of Ag on Syngas Transformation to Long-chain Alcohols over CuFe Catalysts

The Effect of Na Promoter on Fe-Based Catalyst for CO2 Hydrogenation to Alkenes

Effects of Ag Promotion for Co/Al2O3 Catalyst in Fischer-Tropsch Synthesis

Interfacial Fe5C2-Cu catalysts toward low-pressure syngas conversion to long-chain alcohols

Effect of Li Promoter on FeMn/CNTs for Light Olefins from Syngas

Electron‐Deficient Cu Sites on Cu3Ag1 Catalyst Promoting CO2 Electroreduction to Alcohols

Influence of Co Modified Mn/Cu/MgO Catalyst on the Synthesis of Mixed Alcohols from Syngas

Impact of Cu complex anions on CuZnAl intercalated hydrotalcite-like catalysts for low-carbon alcohols synthesis from syngas

Catalytic conversion of syngas to mixed alcohols over CuFe-based catalysts derived from layered double hydroxides

Higher alcohols synthesis from syngas over P-promoted non-noble metal Cu-based catalyst

Tuning the Selectivity of Liquid Products of CO2RR by Cu-Ag Alloying

Tailored alcohol distribution by non-dissociated CO adsorption strength on engineered Cu sites in syngas conversion

Promoter Action of Ag on Cr-Ag/γ-Al2O3 Catalyst for CO Oxidation

Accelerating C2+ Alcohols Synthesis from Syngas by Simultaneous Optimizations of CO Dissociation and Chain Growth over CuCo Alloy Catalyst

Synthesis of mixed higher alcohols over Fe promoted Cu/ZrO2 catalysts by CO hydrogenation

Study of Cu-Fe-Co-M/SiO2 (M = Unpromoted, Li, Na, K and Cs) Catalysts for Mixed Alcohols Synthesis from CO Hydrogenation

Application of Cu-Fe based catalysts in synthesis of low carbon mixed alcohols from syngas

Enhanced CO2-to-CH4 Conversion Via Grain Boundary Oxidation Effect in CuAg Systems

Effect of zinc source on the ethanol synthesis from syngas over a slurry CuZnAl catalyst

Influence of Manganese Promoter on Co-Precipitated Fe–Cu Based Catalysts for Higher Alcohols Synthesis

The effect of CuO crystallite size on the structure and performance of CuZnAl catalyst for mixed alcohols synthesis from syngas