Abstract:The motivation to design a more efficient and compact aircraft engine leads to a continuous increase in overall pressure ratio and decrease in the stage number in compressors. Compared to the traditional multi-stage compressor, a single-stage ultra-high-pressure-ratio centrifugal compressor with a pressure ratio higher than 10.0 can significantly improve the engine’s power-to-weight ratio and fuel economy with a reduced structure complexity. Thus, it has great potential to be adopted in the compression system of advanced aero engines, such as turboshaft engines, in the future. However, the highly narrow Stable Flow Range (SFR) of ultra-high-pressure-ratio centrifugal compressors is a severe restriction for engineering applications. This research focuses on the aerodynamic performance of a ultra-high-pressure-ratio centrifugal compressor, and three-dimensional simulation is employed to investigate the effect of Self-Recirculating Casing Treatment (SRCT) on the performance and stability of the centrifugal compressor. Firstly, the parametric model of SRCT is established to investigate the effect of geometry parameters (rear slot distance and rear slot width) on the aerodynamic performance of the centrifugal compressor. It is concluded that SRCT improves the compressor’s SFR but deteriorates its efficiency. Also, a non-linear and non-monotone relationship exists between the SFR and rear slot distance or width. Then, the flow mechanism behind the effect of SRCT is explored in detail. By introducing the SRCT, an additional flow path is provided across the blade along the circumferential direction, and the behavior of the shock wave and tip leakage flow is significantly changed, resulting in the obviously different loading distribution along the streamwise direction. As a result, the mixing and flow separation loss are enhanced in the impeller flow passage to deteriorate the efficiency. On the other hand, the blockage effect caused by the mixing of slot recirculation and mainstream flow near the impeller inlet increases the axial velocity and reduces the incidence angle below the 90% spanwise section, which is considered to effectively stabilize the impeller flow field and enhance the stability.

Passive Control of Flow Separation with Blade-End Slots for Three-Stage Compressor at Different Reynolds Numbers

Extraction of Geometric Features and Analysis of Flow Mechanism of High Loaded Compressor Airfoils at Low Reynolds Number

Investigation of the Flow Mechanism of a Highly Loaded Compressor Cascade with Upstream Wakes at the Low Reynolds Number Condition

Passive Separation Control with Blade-End Slots in a Highly Loaded Compressor Cascade

Unsteady Flow Mechanism of Corner Separation Control Using Blade End Slots in a Highly Loaded Compressor Cascade

Experimental Investigation of Flow Control Using Blade End Slots in a Highly Loaded Compressor Cascade

Numerical Investigation on the Effects of Re-Organized Shock Waves on the Flow Separation for a Highly-Loaded Transonic Compressor Cascade

Investigation of Control Effects of End-Wall Self-Adaptive Jet on Three-Dimensional Corner Separation of a Highly Loaded Compressor Cascade

Circumferential Propagation Characteristic Of Unsteady Flow In A Subsonic Axial Flow Compressor Rotor At Different Reynolds Numbers

Numerical Study On Flow Separation Control For High-Lift Low-Pressure Turbine Split Blade

Mechanism Study of Stator Suction Slots to Inhibit the Boundary Layer Separation in a Single-Stage Axial Flow Compressor

Effect of Self-Recirculating Casing Treatment on the Aerodynamic Performance of Ultra-High-Pressure-Ratio Centrifugal Compressors

Numerical investigation of boundary layer suction on certain highly loaded aspirated compressor at low speeds

Study Of Low-Speed Modelling Method On Corner Separation Control Using Blade End Slots In A Highly Loaded Compressor Cascade

Passive flow control of the corner separation in an annular compressor cascade with a micro-blade

EVALUATION OF COMPRESSOR BLADING WITH BLADE END SLOTS AND FULL-SPAN SLOTS IN A HIGHLY LOADED COMPRESSOR CASCADE

Influence of Active Flow Control of Synthetic Jet at Suction Surface on the Performance of a Subsonic Axial Compressor Rotor

Numerical Investigation of Three-dimensional Separation Control on a High-speed Compressor Stator Vane with Tailored Synthetic Jet

Numerical Investigation of Active Flow Control Using Tip Synthetic Jet on the Performance of a High-Speed Axial Compressor Rotor

Investigation of the controlling mechanisms of blade slotting technology on the shock-wave-induced corner separation

Combined Flow Control Strategy Investigation for Corner Separation and Mid-Span Boundary Layer Separation in a High-Turning Compressor Cascade