Abstract:Ultrasonic assisted laser welding (ULW) is a newly developed welding method. In this paper, a new kind of ultrasonic assisted laser welding method, which is named trailing ultrasonic assisted laser welding (T-ULW) is proposed. First, the welding temperature fields as well as the weld pool temperature evolution in trailing ultrasonic assisted laser welding (T-ULW) and conventional laser welding (LW) are numerically simulated, and the shapes of the molten pools during T-ULW and LW are observed by a high-speed camera monitoring system. Both the simulation and monitoring results show that ultrasonic can reduce the temperature gradient of the weld pool and prolong the solidification time. Then, such three kinds of welding methods as T-ULW, common fixed-position ultrasonic assisted laser welding (F-ULW) and LW are used to weld SUS301 stainless steel sheet with a thickness of 0.6 mm respectively, and their performances are comparatively investigated by analyzing the experimentally-obtained macro morphologies, microstructures of welded joints. Macro morphology analysis results show that ultrasonic vibration not only elongates the molten pool, but also changes the cross-sectional shapes of the welds in such a way that decreases the top width and increases the bottom width. Microstructure analysis results indicate that the fusion zone of the welds obtained by T-ULW is uniformly distributed mainly by the refined equiaxed grains. Subsequently, the crystal refinement mechanisms of the welds in ultrasonic-assisted laser welds of SUS301 stainless steel are theoretically analyzed and experimentally verified, which show that due to ultrasonic disturbance, the temperature gradient of the molten pool is decreased, a stress field is generated in the welds and a so-called ultrasonic cavitation effect is produced in the molten pool. Such three mechanisms play very important roles in refining crystals in different ways that the decreased temperature gradient provides a good nucleation condition for the growth of equiaxed dendrite, and both the generated stress and ultrasonic cavitation cause the grain boundary to fracture, thereby form more new grain boundary, which finally lead to form fine and uniform grains in the welds. Finally, the mechanical properties of the joints are measured, and the results demonstrated that ultrasonic assisted laser welding especially T-ULW enables not only to increase the tensile strength of the welds, but also to improve the ductility of the welds.

Heat Transfer Characteristics and Enhancement of Weld Properties in Thin Stainless Steel Using Synchronous Cold Air Heat Sink Assisted Laser Welding

Microstructure evolution and mechanical properties of SUS301L stainless steel sheet welded joint in ultrasonic vibration assisted laser welding

Numerical simulation of thermo-mechanical coupling in laser-MIG hybrid welding utilizing dual volume heat sources

Effect of post-weld heat treatment on the microstructure and mechanical properties of laser-welded joints of SLM-316 L/rolled-316 L

Role of Surface-Active Element Sulfur on Thermal Behavior, Driving Forces, Fluid Flow and Solute Dilution in Laser Linear Welding of Dissimilar Metals

Improvement of penetration ability of heat source for 316 stainless steel welds produced by alternating magnetic field assisted laser-MIG hybrid welding

Effect of Dynamic Preheating on the Thermal Behavior and Mechanical Properties of Laser-Welded Joints

Numerical simulation and experimental analysis on the deformation and residual stress in trailing ultrasonic vibration assisted laser welding

Impact of Welding Heat Input on the Mechanical and Corrosion Properties of Lean Duplex Stainless Steel UNS S32001 Laser-Welded Joints

Effect of Ultrasonic Vibration Characteristics on Mechanical Properties of Stainless Steel Laser Weld

Effects of Laser Premelting Treatment on Microstructure and Mechanical Properties of High-Strength Steel Weld Obtained by Laser-MAG Hybrid Welding

Improvement of inhomogeneity of microstructure and mechanical properties for 316 stainless steel laser-MIG hybrid welded joint assisted by alternating magnetic field

Effects of heat source configuration on the welding process and joint formation in ultra-high power laser-MAG hybrid welding

Metallurgical and Mechanical Properties of Underwater Laser Welds of Stainless Steel

Microstructure evolution and mechanical properties in the depth direction of ultra-high power laser-arc hybrid weld joint of 316L stainless steel

Study of Humping Tendency and Affecting Factors in High Speed Laser Welding of Stainless Steel Sheet

A novel approach to regulate energy allocation and melt flow in narrow gap laser welding with electromagnetic assisted wire wobbling

Effects of laser-arc hybrid welding on microstructure and mechanical properties of dissimilar steel joint

Microstructural Characterization of Laser Weld of Hot-Stamped Al-Si Coated 22MnB5 and Modification of Weld Properties by Hybrid Welding

Microstructure and Mechanical Properties of Selective Laser Melting 316L/R-316L Butt Joint Welded by Laser Welding

The research on weld pool morphology and passive film characteristic of high-nitrogen stainless laser-arc hybrid weld joint