Abstract:Cu2O/CuO bilayers were fabricated by electrodeposition of the CuO layer in a copper(II)-ammonia complex aqueous solution, followed by photoelectrochemical deposition of the Cu2O layer at potentials ranging from -0.3 to -1.0 V referenced to a Ag/AgCl electrode in a copper(II)-lactate complex aqueous solution under light irradiation, and the effects of varied potentials of the photoelectrochemical Cu2O depositions and post-heating conditions on their structural, optical, and photovoltaic characteristics were investigated with X-ray diffraction, field emission-scanning electron microscopy, optical absorption measurements, and external quantum efficiency (EQE) measurements with and without applied bias voltage. The Cu2O layers with a characteristic 2.1 eV band gap energy were adhesively stacked on the thorn-like grains of the CuO layers possessing a characteristic 1.5 eV band gap energy, and dense and defect-free Cu2O/CuO bilayers could be fabricated at the potentials of -0.4 and -0.5 V, but the grain size of Cu2O decreased at -0.5 V. In addition, the metallic Cu was deposited simultaneously at potentials less than -0.7 V. The Cu2O/CuO bilayer fabricated at -0.4 V revealed photovoltaic features at wavelengths ranging from 350 nm to approximately 900 nm, and a maximum EQE value of 56.8% was achieved at 510 nm in wavelength with a bias voltage of -0.1 V. The maximum EQE value, however, decreased to 1.2% accompanied with the peak wavelength shift to 580 nm, and no photovoltaic feature was observed at potentials of -0.3, -0.7, and -1.0 V. The photovoltaic performance for the Cu2O/CuO bilayer fabricated at -0.4 V was ameliorated by heating at 423 K, and the maximum EQE values were enhanced to 87.7% at 550 nm and 89.8% at 530 nm in an ambient atmosphere and vacuum. Both the Cu2O and CuO layers acted as photovoltaic layers in the Cu2O/CuO bilayer fabricated at -0.4 V and heated at 423 K, and the electrical characteristic including the carrier mobility affected the photovoltaic performance. The photovoltaic feature, however, disappeared by heating above 523 K due to the formation of nanopores inside the CuO layer and near the CuO heterointerface to the Cu2O and fluorine-doped tin oxide substrate.

Preparation of nanostructured cuprous oxide (Cu2O) absorber layer for photovoltaic application

Microstructure, Morphology and Sunlight Response of Cuprous Oxide Thin Films

An all-sputtered photovoltaic ultraviolet photodetector based on co-doped CuCrO2 and Al-doped ZnO heterojunction

Optimizing the structure and optoelectronic properties of cuprite thin films via a plasma focus device as a solar cell absorber layer

Photoelctrochemically Fabricated and Heated Cu2O/CuO Bilayers with Enhanced Photovoltaic Characteristics

In-Depth Study of Chemically Electrodeposited Cuprous Oxide (Cu2O) thin Films on ITO Glass

Semitransparent Cu2O Films Based on CuO Back Layer for Photoelectrochemical Water Splitting and Photovoltaic Applications

Semitransparent Cu2O films based on CuO Back Layer for Photoelelctrochemical Water Splitting and Photovoltaic Applications

Preparation and Photoelectric Property of Cuprous Oxide Thin Film with Different Morphologies

Thermal optimization of defected Cu2O photon-absorbing layer and the steady p-Cu2O/n-Si photovoltaic application

Standardizing the optimal photo-diode performance of CuO nanostructures through various morphological patterns

Characterizations of Cuprous Oxide Thin Films Prepared by Sol-Gel Spin Coating Technique with Different Additives for the Photoelectrochemical Solar Cell

Photocatalytic Degradation of Cuprous Oxide Nanostructures Under UV/Visible Irradiation

On the structural evolution of nanoporous optically transparent CuO photocathodes upon calcination for photoelectrochemical applications

Study and analysis the Cu nanoparticle assisted texturization forming low reflective silicon surface for solar cell application

Evolution of Structural and Optical Properties of Cuprous Oxide Particles for Visible Light Absorption

Fabrication of Cu2ZnSnS4 Light Absorber Using a Cost-Effective Mechanochemical Method for Photovoltaic Applications

Optical and structural properties of nanostructured copper oxide thin films as solar selective coating prepared by spray pyrolysis method

Aligned 2-D Nanosheet Cu2O Film: Oriented Deposition on Cu Foil and Its Photoelectrochemical Property

Cu 2 O/CuO composite for efficient performance in photoelectrochemical and optoelectronics applications

Cu-rich copper indium sulfide thin films deposited by co-evaporation for photovoltaic applications