Abstract:Microwave dielectric ceramics are vital for filters, dielectric resonators, and dielectric antennas in the 5G era. It was found that the (Cu1/3Nb2/3)4+ substitution can effectively adjust the TCF (temperature coefficient of resonant frequency) of Li2TiO3 and simultaneously increase its Q × f (Q and f denote the quality factor and the resonant frequency, respectively) value. Notably, excellent microwave dielectric properties (εr (permittivity) ≈ 18.3, Q × f ≈ 77,840 GHz, and TCF ≈ +9.8 ppm/°C) were achieved in the Li2Ti0.8(Cu1/3Nb2/3)0.2O3 (LTCN0.2) ceramic sintered at 1140 °C. Additionally, the sintering temperature of LTCN0.2 was reduced to 860 °C by the addition of 3 wt % H3BO3, exhibiting superior microwave dielectric properties (εr ≈ 21.0, Q × f ≈ 51,940 GHz, and TCF ≈ 1.4 ppm/°C) and being chemically compatible with silver. Moreover, LTCN0.2 + 3 wt % H3BO3 ceramics were designed as a patch antenna and a dielectric resonator antenna, both of which showed high simulated radiation efficiencies (88.4 and 93%) and gains (4.1 and 4.03 dBi) at the center frequencies (2.49 and 10.19 GHz). The LTCN0.2 + 3 wt % H3BO3 materials have promising future application for either 5G mobile communication devices and/or in low-temperature co-fired ceramic technology owing to their high Q, low sintering temperature, small density, and good temperature stability.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18836?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18836</a>.Refined lattice parameters of LTCNx (0 ≤ x ≤ 0.4) ceramics (Table S1), Raman spectra of LTCNx (0 ≤ x ≤ 0.4) ceramics (Figure S1), SEM images and densities of the LTCNx (0 ≤ x ≤ 0.4) specimens (Figure S2), phonon parameters achieved from the fitting of the infrared reflectivity spectra of the LTCN0.2 specimen (Table S2), phonon parameters achieved from the fitting of the infrared reflectivity spectra of the LTCN0.2 + 3 wt % H3BO3 ceramic (Table S3), and optimized parameters of the proposed patch antenna (Table S4) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18836/suppl_file/am0c18836_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Design of Low Temperature (54 K) Reusable Test Fixture Based on Pogo Pin and Al2O3 HTCC Ceramics

Low-temperature Co-Fired Ceramics with High Thermal Expansion and Reliability for Millimeter-Wave Antennas

A Compact 2-18Ghz Ultra-Wideband Frequency-conversion T/R Module Based on a 3D Heterogeneous Integrated Process

Design and Fabrication of a TR Microsystem in Ka Band with Si-Based 3D Heterogeneous Integration

Development of a Low-power Consumption Cryogenic MMIC LNA for Immediate Connection with an SIS Mixer

Design And Fabrication Of Cryogenic Low Noise Amplifier In Low Rf Band

A DESIGN OF Ku-BAND CRYOGENIC LOW-NOISE AMPLIFIER

Development of cryogenically-cooled low noise amplifier for mobile base station receivers

Investigation on Temperature Behavior for a GaAs E-pHEMT MMIC LNA

The design and fabrication of low RF CLNA for HTS receiver

R&D Towards Cryogenic Optical Links

Characteristics Of Low Noise 800mhz Amplifier At Cryogenic Temperature

Low Noise Amplifier in HTS System

CRYOGENIC CHARACTERISTICS OF HIGH ELECTRON MOBILITY TRANSISTOR AND LOW NOISE AMPLIFIERS

Design and Measurement of P Band Cryogenic Low Noise Step Amplifier

A Cryogenic Sige Low Noise Amplifier Developed for Radio Astronomy

Design of a High-Efficiency and -Gain Antenna Using Novel Low-Loss, Temperature-Stable Li 2 Ti 1 – x (Cu 1/3 Nb 2/3 ) x O 3 Microwave Dielectric Ceramics

Low-noise amplifier cryogenic testbed validation in a TaaS (Testing-as-a-Service) framework

Design and Development of SIS Mixers for ALMA Band 10

High Q and high gradient performance of the first medium-temperature baking 1.3 GHz cryomodule

Cryogenic Modeling of GaAs-pHEMT and its Application in Low-power MMIC CLNA Design for Radio Astronomy