Abstract:In this study, we investigated the effects of nanostructured composite powders (WC-Ni), nickel binder content, and sintering techniques on the morphology and mechanical properties of tungsten carbide. An alternative low-temperature gas-solid reaction route with a short reaction time was employed to produce nanostructured composite powders with 5 and 15 wt% Ni. The powders were consolidated using spark plasma sintering (SPS) and conventional vacuum furnace sintering at temperatures of 1350 °C and 1450 °C. The composite powders were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and particle size measurements. The expansion/contraction of the compacted nanocomposite powders was studied through dilatometric analysis. The composite powders exhibited a uniform distribution of Ni, in both compositions. For the WC-5 wt% Ni nanocomposite powders, the average crystallite sizes for WC and Ni were 41.6 nm and 46.2 nm, respectively. While, for the WC-15 wt% Ni nanocomposite, the crystallite sizes for WC and Ni were 45.6 and 38.4 nm. The sintered composites were evaluated through XRD, SEM, measurements of density and Vickers hardness. The enhanced sinterability of the nanostructured powders enabled their consolidation into (WC-Ni) hard metal with densities approaching the theoretical relative density of 96.07 %, even with low binder content (5 wt% Ni). This is attributed to the uniform distribution of Ni and an extensive Ni-WC interface present prior to sintering. The SPS process at 1350 °C produced sintered bodies (WC-5 wt% Ni and WC-15 wt% Ni) with higher Vickers hardness (2322 HV and 1512 HV, respectively) and superior microstructural quality compared to samples produced by conventional vacuum furnace techniques. These results demonstrated that the mechanical properties of the system WC-Ni processed by SPS are superior to those obtained by vacuum furnace. Therefore, WC-Ni hard metals processed by this approach is a promising alternative to conventional hard metals (WC-Co) for a wide range of applications.

Study on Process Optimization of Electroless Ni-P Plating on Binderless WC

Enhanced electroless Ni-P plating quality on binderless tungsten carbide by atmospheric pressure plasma pretreatment

Study on electrochemical anodization initiation and progression of binderless tungsten carbide (WC) through experimentation and simulation

Study on Electroless Plating Ni-W-P Ternary Alloy with High Tungsten from Compound Complexant Bath

Determination of selective laser melting process parameters of tungsten carbide powders coated with nickel via electroless plating for improved interface properties

Exploration of Pretreatment Process and Wettability of High Bonding Ni-P Coatings on W-Cu Composites for Electronic Packaging

Influence on (Ni-P) Electroless Composite Plating with Carbon Nanotubes

Effect of Ni Content on Microstructure and Properties of WC-Ni Composites Prepared by Electroless Plating and Powder Metallurgy

Preparation of Nickel-Coated Tungsten Carbide Powders by Room Temperature Ultrasonic-Assisted Electroless Plating

Optimization of Process Parameters on Surface Integrity in Wire Electrical Discharge Machining of Tungsten Tool YG15

Research on Ni-WC Coating and a Carbide Solidification Simulation Mechanism of PTAW on the Descaling Roll Surface

Study on Direct-Current Electroplated Ni-W-P Layer

Effect of WC-Ni Powder Composition and Preparation on Cold Spray Performance

A new electroless nickel deposition technique to metallise SiCp/Al composites

A New Process for Efficient Non-Destructive Metal-Activated Composite Plating of Ni-P-Al2O3 on Titanium Base and Its Performance Research

A comprehensive study on electrochemical polishing of tungsten

Study of properties of Ni-base nano-ZrO2 composite plating coatings

Electroless Nickel on the Surface of SiCp/Al Composites

Enhanced properties of hard metal WC-Ni processed from nanostructured powders

Preparation and Properties of Ni–W Composite Coatings Reinforced by Graphene Nanoplatelets

Study of Electroless Ni-P Process and Wastewater Treatment