Abstract:The use of carbon fiber reinforced plastic (CFRP) is rapidly increasing in aerospace and automobile applications. This is in large part due to the increase strength and modulus of carbon fiber composites compared to other materials such as glass fiber composites. The fiber-matrix interface has been found to be important for high strength in composites. Methods that have been studied and developed to improve interfacial property of composites include: the addition of coupling agents, surface modifications, chemical reaction control and use of nano-fillers for reinforcement. During mechanical loading the shape of carbon fibers, in a composite, is altered with a concomitant change in electrical resistance. Carbon fibers are used as sensing elements in CFRP due to their electrical conductivity. In some more advanced studies, in CRFP, the carbon fibers were used for both strain sensing and damage sensing. The basic theory, in such studies, was that the movement of carbon fiber could be detected by electrical resistance measurement. During loading, the extent of contact between carbon fibers in a CF tow is altered, and the electrical resistance changes from its initial value. In this work, interfacial properties of carbon fiber/polymer composites were evaluated by such electrical resistance measurements. During the wetting process of CF tows by the polymer resins, the change in electrical resistance was recorded and analyzed. The test results for different carbon fibers and polymer resins exhibited different trends. The electrical resistance change was associated with the different wetting conditions, and the interfacial properties were predicted by these electrical resistance measurements. CF tow/epoxy exhibited the poorest carbon tow wettability, the smallest change in resistance and the poorest IFSS and ILSS. For the four systems studied, the relative change in each of these quantities for the materials of a given composite was roughly proportional to the other measured quantities. This may have some very significant practical importance. It may point the way to use quick easy tests to screen and predict other behaviors for composites of different materials and/or processes. Perhaps a simple resistance change test might be used to predict and select good candidate materials, surface processing techniques for high strength composite applications. The proportional relationship between interfacial adhesion and electrical resistance change was obtained by trend fitting line analyses. Ultimately, it was demonstrated that mechanical properties related to interfacial properties might potentially be predicted by electrical resistance measurement and studies of wetting behavior, using empirical formulas and correlations.

Resistor Network for Forward Calculation in Electrical Resistance Tomography of Carbon Fiber Reinforced Composites

A New Electrical Resistance Measurement Method of Carbon Fiber-Reinforced Polymer Tubes Based on C⁴D Technique

Modeling and optimal design of sensor for capacitively coupled electrical resistance tomography system

Interfacial Evaluation Of Carbon Frinforced Nano-Composites Using Electrical Resistance Measurement With Wetting Tests

A novel electrical resistance tomography system based on C4D technique

Image Reconstruction Algorithm for Capacitively Coupled Electrical Resistance Tomography

Review of Self-Sensing of Damage and Interfacial Evaluation Using Electrical Resistance Measurements in Nano/micro Carbon Materials-Reinforced Composites

Ultrasonic Inspection Of Localized Defects In Low-Porosity Cfrp

A Novel Electrical Resistance Tomography System Based on ${\rm{c}}^{4}{\rm D}$ Technique

A Two-Stream Deep Imaging Method for Multifrequency Capacitively Coupled Electrical Resistance Tomography

Optimum Design for Capacitively Coupled Electrical Resistance Tomography Sensor Configuration

Reconstruction of Cracks in a Carbon Fiber-Reinforced Polymer Laminate Plate from Signals of Eddy Current Testing

Impact damage localization and mode identification of CFRPs panels using an electric resistance change method

Efficient Near-Field Radiofrequency Imaging of Impact Damage on CFRP Materials with Learning-Based Compressed Sensing

Research on Piezoresistive Effect and Random Model of Carbon Fiber Bundle

A new probe‐based electromagnetic non‐destructive testing method for carbon fiber‐reinforced polymers utilizing eddy current loss measurements

Damage detection in carbon fiber–reinforced polymer composite via electrical resistance tomography with Gaussian anisotropic regularization

Classification and Characterization of Damage in Composite Laminates Using Electrical Resistance Tomography and Supervised Machine Learning

Noncontact Visualization of Multiscale Defects in CFRP Composites using Eddy Current Testing with T-R Probe

Non-Destructive Testing of Carbon Fiber-Reinforced Plastics (CFRPs) Using a Resonant Eddy Current Sensor

Tensile damage self-monitoring of carbon fiber/epoxy 3D braided composites with electrical resistance method