Abstract:In machining, heat concentration is generated at the surface contact between the tool and workpiece. This is the effect of hard frictions at the shear cutting plane to remove hard and brittle materials. The highly adhesive behavior of aluminum alloy 6061-T6 is more severe in higher cutting temperature, which may affect tool failures such as flank wear, tool chip and built-up edge, particularly on the edge of cutting inserts during the process. As a result, this may lead to the rough surface and low-dimensional accuracy of the machined parts. Realizing that metal-cutting industry players are demanding high-quality products with better surface finish and dimensional accuracy led to this study. Aluminum alloy 6061-T6 is a standard alloy used in automotive, aerospace and food packaging due to good hardness, high strength-to-weight ratio, resistance to corrosion and weldability. In order to address this problem, a newly developed metal working fluid which is SiO2-Al2O3-ZrO2 tri-hybrid nanofluid is applied in the cutting zone to achieve a good surface finish of the machined parts and lowering the cutting temperature. This study is the first attempt to enhance machining performance, particularly at high-speed machining, by employing a combination of tri-hybrid nanofluids and a minimum quantity lubricant technique. Industrial standards include uncoated tungsten carbide and CVD TiCN-Al2O3 carbide used during machining of aluminum alloy 6061-T6. The minimum quantity lubricant method is an alternative in supplying the lubricant into the machining zone due to flood machining and conventional fluid possess safety, health, economic and environmental effects. In this study, the experimental data were analyzed statistically using analysis of variance and response surface methodology. The responses studied were reduced significantly when tri-hybrid nanoparticles present at the cutting interface with higher MQL flow rate and concentration. There are two-factor interactions which are significant to the responses studied. Therefore, the combinations of MQL and excellent tri-hybrid nanofluids characteristics have enhanced between 16 and 76% of surface roughness and the cutting temperature, respectively, which is very promising in the future.

Effect of Hbn/mos2 Hybrid Nanofluid Minimum Quantity Lubrication on the Cutting Performance of Self-Lubricating Ceramic Tools when Machining AISI 4340

Effect of hBN/MoS 2 hybrid nanofluid minimum quantity lubrication on the cutting performance of self-lubricating ceramic tools when machining AISI 4340

Machinability Assessment of Hybrid Nano Cutting Oil for Minimum Quantity Lubrication (MQL) in Hard Turning of 90CrSi Steel

Tribology and machinability performance of hybrid Al2O3 -MWCNTs nanofluids-assisted MQL for milling Ti-6Al-4 V

Influence of MoS2-Based Nanofluid Minimum Quantity Lubrication on Machining Performance of AISI 316L Stainless Steel

Design, optimization, and verification of self‐lubricating ceramic tool microstructure by MC method

Effects of SiO2-Al2O3-ZrO2 Tri-hybrid Nanofluids on Surface Roughness and Cutting Temperature in End Milling Process of Aluminum Alloy 6061-T6 Using Uncoated and Coated Cutting Inserts with Minimal Quantity Lubricant Method

Temperature Analysis in Cubic Boron Nitrate Cutting Tool during Minimum Quantity Lubrication Turning with a Coconut-Oil-Based Nano-Cutting Fluid Using Computational Fluid Dynamics

A Study on the Effects of Hybridized Metal Oxide and Carbonaceous Nano-Cutting Fluids in the End Milling of AA6082 Aluminum Alloy

Using Nano-Fluids Minimum Quantity Lubrication (NF-MQL) to Improve Tool Wear Characteristics for Efficient Machining of CFRP/Ti6Al4V Aeronautical Structural Composite

Experimental Investigation on the Compatibility of Nanoparticles with Vegetable Oils for Nanofluid Minimum Quantity Lubrication Machining

Investigation of Surface Integrity of 304 Stainless Steel in Turning Process with Nanofluid Minimum-Quantity Lubrication Using h-BN Nanoparticles

Cold Plasma and Different Nano-Lubricants Multi-Energy Field Coupling-Assisted Micro-Milling of Al-Li Alloy 2195-T8 and Flow Rate Optimization

Grindability Evaluation of Ultrasonic Assisted Grinding of Silicon Nitride Ceramic Using Minimum Quantity Lubrication Based SiO2 Nanofluid

Microstructure and performance optimization of Al2O3/TiC/TiB2/h-BN@Al2O3 self-lubricating ceramic tool materials

An Investigation on the Tribological Performances of the SiO 2 /mos 2 Hybrid Nanofluids for Magnesium Alloy-Steel Contacts

Improving the frictional properties of the tool/chip interface of micro-textured ceramics tools by using electromagnetic-assisted nanofluids

Effects of Ultrasonic Nanolubrication on Milling Performance and Surface Integrity of SiCp/Al Composites

Influence of self-lubricating elements (SrSO4, Mo, and CaF2) on machining performance of Al2O3-ZrO2 (Y2O3)-NiCr-Ag cutting tool over a wide cutting speed range

Effect of MQL condition on cutting performance of high-speed machining of GH4099 with ceramic end mills

Study on the Cooling and Lubrication Mechanism of Magnetic Field-Assisted Fe3O4@CNTs Nanofluid in Micro-Textured Tool Cutting