Abstract:Fe-6.5wt% Si non-oriented electrical steel sheets with a thickness of 0.50mm were produced by using a new processing route: strip casting followed by hot rolling, intermediate temperature (150–850°C) rolling and final annealing. The present study focused on exploring the effects of rolling temperature varying from 150 to 850°C on the microstructure and texture evolution, the formability and final magnetic properties. The microstructure and texture evolution at the various processing steps were investigated in detail by using OM, XRD, EBSD and TEM. It was found that the formability during rolling, the microstructure and texture before and after annealing and final magnetic properties highly depended on rolling temperature. The formability during rolling was gradually improved with increasing rolling temperature due to the slipping of dislocation. In particular, the rolling temperature dominated the formation of in-grain shear bands in the rolled microstructure, which played an important role in the development of final recrystallization microstructure and texture. In the case of lower temperature (150–450°C) rolling, an inhomogeneous microstructure with a large amount of in-grain shear bands was formed in the rolled sheets, which finally resulted in a fine and inhomogeneous annealing microstructure dominated by mild λ-fiber texture composed of cube and {001}〈210〉 components and α*-fiber texture concentrated on {115}〈5–10 1〉 component. By contrast, in the case of higher temperature (650–850°C) rolling, a relatively homogeneous microstructure without in-grain shear bands was formed instead in the rolled sheets, which finally led to a coarse and relatively homogeneous annealing microstructure characterized by strong α-fiber and γ-fiber texture. Accordingly, on the whole, both the magnetic induction (B8 and B50) and iron loss (P15/50 and P10/400) decreased with raising rolling temperature.

Texture Genetics and Magnetic Properties of Fe-6.5%Si Materials Modified with Cu

Achieving Homogeneous Fe Distribution and High Strength in Cu-Fe Composite Consolidated by Powder Rolling

Microstructure, Texture Evolution And Magnetic Properties Of Fe-6.5 Wt. % Si And Fe-6.5 Wt. % Si-0.5 Wt. % Cu Alloys During Rolling And Annealing Treatment

The influence of cooling rate on microstructure and magnetic properties of cast Fe-6.5wt%Si steel

A study of electromagnetic characteristics of Fe-Si-Al magnetic alloy

Experimental Study on the Twin Roll Strip Casting and Warm Rolling Fe-6.5 Wt. %si Steel Sheet

Evolution from Amorphous to Nanocrystalline and Corresponding Magnetic Properties of Fe-Si-B-Cu-Nb Alloys by Melt Spinning and Spark Plasma Sintering

Effects of Si addition on mechanical, electrical and magnetic property of Cu-10Fe alloy

Microstructure, Texture and Magnetic Properties of Strip Casting Fe–6.2 Wt%si Steel Sheet

Characterization of the Fe-6.5wt%Si Strip with Rapid Cooling Coupling Deep Supercooled Solidification

Microstructure & Texture Evolution and Magnetic Properties of High Magnetic-Induction 6.5% Si Electrical Steel Thin Sheet Fabricated by A Specially Designed Rolling Route

Development of Λ-Fiber Recrystallization Texture and Magnetic Property in Fe–6.5wt% Si Thin Sheet Produced by Strip Casting and Warm Rolling Method

Effects of rolling temperature on microstructure, texture, formability and magnetic properties in strip casting Fe-6.5wt% Si non-oriented electrical steel

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Dislocation Strengthening and Texture Evolution of Non-Oriented Fe-3.3 wt% Si Steel in Double Cold Rolling

A comprehensive study on texture evolution and recrystallization mechanism of Fe-4.5 wt% Si with strong {114}

TEXTURE CHARACTERISTICS OF Fe-6.5%Si SHEETS PRODUCED BY THE DEPOSITIONDIFFUSION METHOD

The Evolution of Microstructure and Magnetic Properties of Fe–Si–Cr Powders on Ball-Milling Process

Effect of 0.5 Mass% Cu Addition on Ductility and Magnetic Properties of Fe-6.5Si Alloy

Microstructure evolution and soft magnetic properties of Cu–10Fe alloys

Microstructure and soft magnetic properties of nanocrystalline Fe–Si powders