Abstract:For aluminum-based alloy particles, the addition of alloying element lithium (Li) with the properties of a high chemical activity and a low melting/boiling point can significantly improve the thermo-reactive properties of aluminum (Al) particles. To further reveal the combustion mechanism, this paper presents the nitriding reaction and combustion characteristics of Al-Li alloy in nitrogen (N 2 ) through thermogravimetric analysis and differential scanning calorimetry (TG-DSC) analysis at a low heating rate and laser-induced ignition experiments at a high heating rate, considering the influences of two kinds of Li contents (1.0 wt% @ Al-1.0Li and 2.5 wt% @ Al-2.5Li) on these characteristics and making a comparison to the counterpart Al. Al-Li alloy powders as-prepared by gas atomization method showed the texture of the Li-rich eutectic phase compounds on the surface by scanning electron microscope (SEM) characterization. The TG-DSC results demonstrated that the thermal nitriding reaction of Al-Li alloy in N 2 was significantly faster than that of pure Al. The nitriding reaction temperature decreased from 853 °C for pure Al to 245 °C for Al-2.5Li alloy with a reduction of 71 %. The final weight gain of Al-2.5Li alloy was almost three times higher than that of pure Al in N 2 . The SEM photograph of intermediate nitriding products revealed that the cracks and loose "island" structures in the Li-rich zone on the Al-Li surface were the key to preventing the formation of a "passivation effect" into Al and promoting N 2 uptake during melting. In addition, Li also acts as a catalytic carrier and "oxygen absorber" to enhance the Al-N reaction. The combustion of single Al-Li alloy microparticles induced by laser showed two stages: preheating and rapid nitriding. Al-Li alloy particles were ignited more rapidly and showed typical gas-phase / surface combustion modes different from pure Al. According to these findings, the combustion mechanism was proposed to help guide the development of Al-based solid propellants containing Li and the synthesis of AlN/Al composites in nitrogen-rich environments.

Selective Coating Fabrication and Combustion Performance of Al-5Li Alloy Particles with High Stability and Compatibility with HTPB

Stabilization Coating of Aluminum-Lithium Alloy and Its Application in Propellant

Preparation of core-shell structured Al-5Li@HTPB powders with improved stability and combustion performance by using perfluoroalkylsilane as a surfactant

Preparation of high-energy Al-Li alloy powders with enhanced compatibility and combustion performance by dense fluorosilane polymer composite coating

Combustion performance modulation and agglomeration inhibition of HTPB propellants by fine Al/oxidizers integration

The Effect of Li-Al Alloy on Combustion Performance of B/PTFE Fuel-Rich Propellant

Study on a novel Al-B-Li alloy powder with high enthalpy of combustion

Laser-Induced Ignition and Combustion of Single Micron-Sized Al-Li Alloy Particles in High Pressure Air/N2

Ignition and combustion of Al–Mg–Li alloy particles at elevated pressures

Polyphenols-inspired interface modification and reduced agglomeration of solid propellants via a functionalized fluorine-containing organic substance coating layer

Modifying the ignition, combustion and agglomeration characteristics of composite propellants via Al-Mg alloy additives

TF-Al/TiC highly reactive composite particle for application potential in solid propellants

Condensed Combustion Products Characteristics of HTPB/AP/Al Propellants under Solid Rocket Motor Conditions

Combustion behavior of AP/HTPB/Al composite propellant containing hydroborate iron compound

Enhancement effect of Li addition on nitriding reaction and combustion of Al-Li alloy in N 2

Enhanced stability and combustion performance of AlH3 in combination with commonly used oxidizers

Effect of complex metal hydride on the thermal decomposition behavior of AP/HTPB-based aluminized solid rocket propellant

Effects of AlH 3 particle size and loading on the combustion and agglomeration of solid propellants

The effect of Al/oxidizers interfacial structure on the mechanical properties of composite propellants

Research on the Combustion Properties of Propellants with Low Content of Nano Metal Powders

Characterization of an Aluminum–Lithium-Alloy-Based Composite Propellant at Elevated Pressures