Abstract:Laser-based metal additive manufacturing technology, which is represented by laser powder bed fusion (LPBF) and direct energy deposition (DED), has been widely used in high-end industries such as aerospace. However, with the rapid development of aerospace equipment, it has become increasingly difficult to meet the requirements of integrated design and manufacturing of metal parts by using LPBF or DED alone. LPBF/DED hybrid laser additive manufacturing technology is expected to greatly improve the overall manufacturing capacity of metal components by combining the advantages of the two technologies. It is expected to break through the limitation of overall manufacturing size, to realize the manufacturing of large and complex aerospace parts, and to reduce the number of components required for large and complex structures to meet the overall design and manufacturing requirements. In this paper, AlSi10Mg was selected as the build material for the LPBF/DED hybrid laser additive manufacturing process and the microstructure and mechanical properties of the as-built samples were studied. The analyses of the microstructure show that there are no obvious defects at the interface between the LPBF zone and the DED zone. Although the phase compositions of both the LPBF zone and the DED zone are composed of alpha-Al matrix and eutectic Si, the melt track shape, microstructural morphology, grain size, grain boundary angle distribution and grain texture change significantly around the LPBF/DED interface. The results of mechanical property tests indicated that the LPBF zone has higher microhardness and tensile strength but lower elongation in comparison with the DED zone. The fine microstructure containing a large number of Si-rich nano-precipitates and high amount of solid solution element enhance the microhardness and tensile strength of the LPBF zone, where the lower solid solubility and high percentage of low angle grain boundary increased the elongation of the DED zone. More importantly, the tensile strength of the LPBF/DED interface is not less than the DED zone, and the boundary of DED melt track as well as porosity defect in the DED zone are the weakest region of LPBF/DED hybrid laser additive manufacturing AlSi10Mg specimens. Therefore, the overall tensile strength of the sample is mainly determined by the DED zone. The formation mechanism of the gradient microstructure around the LPBF/DED interface and the effect of microstructure on properties were also analyzed. This paper proves that the LPBF/DED hybrid laser additive manufacturing technology can be used for the overall manufacturing of aluminum alloy components with regular surface structure.

Comparative Analysis of Microstructure and Mechanical Properties in FeMnAlNi Alloys Fabricated Via Casting and Additive Manufacturing

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Effects of the microstructure and texture characteristics on mechanical properties of the Al–Ni–Cu–Fe alloy manufactured by laser powder bed fusion

Microstructure and Mechanical Behavior of Additively Manufactured CoCrFeMnNi High-Entropy Alloys: Laser Directed Energy Deposition versus Powder Bed Fusion*

Phase constitution, microstructure and mechanical properties of a Ni-based superalloy specially designed for additive manufacturing

Comparing microstructure and mechanical properties of AlSi10 alloy produced by powder bed fusion-laser beam and high pressure die casting

Microstructures and mechanical properties of a modified 9Cr ferritic-martensitic steel in the as-built condition after additive manufacturing

Approach to Estimate the Phase Formation and the Mechanical Properties of Alloys Processed by Laser Powder Bed Fusion via Casting

Microstructures and Mechanical Properties of CrMnFeCoNi High Entropy Alloys Fabricated Using Laser Metal Deposition Technique

The Microstructure and Magnetic Properties of a Soft Magnetic Fe-12Al Alloy Additively Manufactured via Laser Powder Bed Fusion (L-PBF)

Phase transformation and microstructural evolution in Al-Mn-Fe-Si 3104 aluminum alloy made by laser directed energy deposition

Revealing the influence of Fe on Fe-rich phases formation and mechanical properties of cast Al-Mg-Mn-Fe alloys

Simultaneously Enhanced Strength-Ductility of AlCoCrFeNi 2.1 Eutectic High-Entropy Alloy Via Additive Manufacturing

Evolution of microstructure and mechanical properties in 2205 duplex stainless steels during additive manufacturing and heat treatment

Microstructure and mechanical properties of AlSi10Mg alloy built by laser powder bed fusion/direct energy deposition hybrid laser additive manufacturing

The Printability, Microstructure, and Mechanical Properties of Fe80−xMnxCo10Cr10 High-Entropy Alloys Fabricated by Laser Powder Bed Fusion Additive Manufacturing

High throughput in-situ synthesis of Fe-Cr-Ni alloys via laser powder bed fusion: exploring the microstructure and property evolution

A comparative study on WE43 magnesium alloy fabricated by laser powder bed fusion coupled with deep cryogenic treatment: Evolution in microstructure and mechanical properties

Achieving exceptional work-hardening capability of additively-manufactured multiphase Fe-Mn alloys via multiple deformation mechanisms

Microstructure, mechanical properties and strengthening mechanisms of IN738LC alloy produced by Electron Beam Selective Melting

Mechanical properties and microstructural evolution of a novel (FeCoNi)86.93Al6.17Ti6.9 medium entropy alloy fabricated via powder metallurgy technique