Abstract:The metallic interconnects are essential components of energy devices such as fuel cells and electrolysis cells, batteries, as well as electronics and optoelectronic devices. In recent years, 3D printing processes have offered complementary routes to the conventional photolithography- and vacuum-based processes for interconnect fabrication. Among these methods, the confined electrodeposition (CED) process has enabled a great control over the microstructure of the printed metal, direct printing of high electrical conductivity (close to the bulk values) metals on flexible substrates without a need to sintering, printing alloys with controlled composition, printing functional metals for various applications including magnetic applications, and for in situ scanning electron microscope (SEM) nanomechanical experiments. However, the metal deposition rate (or the overall printing speed) of this process is reasonably slow because of the chemical nature of the process. Here, we propose using the CED process to print a single layer of a metallic trace as the seed layer for the subsequent selected-area electroless plating. By controlling the activation sites through printing by the CED process, we control, where the metal grows by electroless plating, and demonstrate the fabrication of complex thin-film patterns. Our results show that this combined process improves the processing time by more than 2 orders of magnitude compared to the layer-by-layer printing process by CED. Additionally, we obtained Cu and Ni films with an electrical resistivity as low as ∼1.3 and ∼2 times of the bulk Cu and Ni, respectively, without any thermal annealing. Furthermore, our quantitative experiments show that the obtained films exhibit mechanical properties close to the bulk metals with an excellent adhesion to the substrate. We demonstrate potential applications for radio frequency identification (RFID) tags, for complex printed circuit board patterns, and resistive sensors in a Petri dish for potential biological applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.1c01890?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.1c01890</a>.SEM images of the single-layer printed Cu and Ni lines with a nozzle diameter of ∼250 μm for different nozzle speeds; The optical images of single-layer Cu and Ni lines printed with different nozzle speeds, and the width and thickness of the printed Cu and Ni lines vs the nozzle speed; The FIB-sectioned cross-sectional images of Cu and Ni films; and The schematic of an unpinned (top) and pinned (bottom) indentation-induced buckle (<a class="ext-link" href="/doi/suppl/10.1021/acsami.1c01890/suppl_file/am1c01890_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Quality Assessment of Metal Traces Manufactured by Localized Electrochemical Deposition Printing and Electroless Plating

Interconnect Fabrication by Electroless Plating on 3D-Printed Electroplated Patterns

Hybrid Printing of Conductive Traces from Bulk Metal for Digital Signals in Intelligent Devices

Meniscus-confined Electrodeposition of Metallic Microstructures with In-Process Monitoring of Surface Qualities

Solution-based, additive fabrication of flush metal conductors in plastic substrates by printing and plating in two-level capillary channels

Fabrication of Shape‐Controlled Copper Line Arrays by Meniscus‐Confined 3D Microprinting on Insulating Substrates

Intercircuit: Electroplating with Cavities for Fast Fabrication of Complex and High-Performance 3D Circuits

3D Printing of Multi-Metallic Microstructures by Meniscus-Confined Electrodeposition.

MOEMS 3D microstructure preparation method based on novel localized electrochemical deposition

Voxelated Meniscus-Confined Electrodeposition of 3D Metallic Microstructures

Quantitative calibration of conductive pattern growth via electroless copper plating at nano-resolution

Microstructure-driven electrical conductivity optimization in additively manufactured microscale copper interconnects

Direct visualization of nanoparticle morphology in thermally sintered nanoparticle ink traces and the relationship among nanoparticle morphology, incomplete polymer removal, and trace conductivity

Shrinkage and deformation compensation in metal fused filament fabrication (mf3) sintered copper components using 3d scanning and inverse deformation

Electrical property-microstructure of copper interconnects printed by localized pulsed electrodeposition (l-PED)

Extreme Drop Durability of Sintered Silver Traces Printed With Extrusion and Aerosol Jet Processes

Formulation of Screen-Printable Cu Molecular Ink for Conductive/Flexible/Solderable Cu Traces

In-process non-destructive evaluation of metal additive manufactured components at build using ultrasound and eddy-current approaches

Microstructure and Residual Stress Gradient Evolution Mechanism of Electronic Copper Strip for Lead Frame

Localized Electrochemical Deposition Using Copper Pyrophosphate-Based Electrolyte

Electroplating of Aerosol Jet‐Printed Silver Inks