Abstract:6xxx alloys have become of particular interest in automotive structural applications as replacements for low carbon steels, mainly because of the increasing demand for the utilization of lighter materials in the automotive industry. However, the strength and formability of the 6xxx alloy are inferior to those of fully annealed low carbon steels, which is partially due to the different crystallographic textures of these two materials. In-situ nanoparticle-reinforced composites have always been extensively used due to their high modulus, high strength, specific stiffness and excellent comprehensive properties. However, traditional in-situ methods require long reaction time and high reaction temperatures, leading to further growth or agglomeration of the reinforcement particles and decreasing the mechanical properties. In this work, in-situ ZrB2/AA6111 composites were successfully prepared via an in-situ melt reaction with the assistance of an electromagnetic field. The effect of electromagnetic field on distribution, size and morphology of in-situ particles, interface structure between particles and matrix, and dislocation morphology in composites were characterized by XRD, OM, SEM and TEM. The action mechanism of electromagnetic field and the effect of microstructure on tensile strength were analyzed. The results indicated that with the assistance of electromagnetic field during in-situ reaction, the large particle clusters were broken into smaller clusters that were uniformly distributed in the matrix, the distribution of ZrB2 nanoparticles was diffused and homogeneous with the size decreasing to 50 similar to 100 nm, and the corners of the nanoparticles clearly became obtuse. In addition, the interface between the particles and the matrix was well bonded without any impurities. The uniformity of the ZrB2 nanoparticle distribution improved, resulting in dislocation propagation and entanglement. When electromagnetic frequency was 10 Hz, the optimal ultimate tensile strength (UTS), yield strength (YS) and elongation (EI) of the composites prepared under the electromagnetic field were 362 MPa, 253 MPa and 25%, respectively, correspondingly increasing 38.7%, 68.6% and 28.7% over the respective properties of the ZrB2 (np)/AA6111 composite. These improvements were due to the Orowan strengthening, load transmitting strengthening, grain refinement strengthening, and dislocation strengthening caused by the nano-sized ZrB2 particles synthesized under the coupled electromagnetic and ultrasonic field. In addition, the Orowan strengthening contributed most to the improvement of properties.

Insight into Microstructure Evolution of In-Situ ZrB2np/AA6111 Composites with Both Excellent Room and High Temperature Properties

Effects of ZrB2 Nanoparticles on the Microstructures and Tensile Properties of a Hot Extruded In Situ AA6111 Composite

Microstructure and Properties of In-Situ ZrB2 (np)/aa6111 Composites Synthesized under an Electromagnetic Field

Investigation on high-temperature creep property and mechanism of AA6111 matrix composites reinforced by in-situ ZrB 2 nanoparticles

Microstructure Evolution and High-Temperature Performances of AA6111 Alloy Strengthened by Sc, Zr Co-Microalloying

Microstructure-property Analysis of ZrB2/6061Al Hierarchical Nanocomposites Fabricated by Direct Melt Reaction

Microstructures and mechanical properties of the in-situ formed nanocomposites of (ZrB2 + Al2O3) and AA7055 alloy

Microstructure evolution and mechanical properties of in-situ ZrB2/Al7085 nanocomposites during hot rolling deformation

In Situ Fabrication and Microstructure of Micro-Nano ZrB2p/Al Composites

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Effects of in-situ ZrB 2 nanoparticles and scandium on microstructure and mechanical property of 7N01 aluminum alloy

Microstructure of ZrB<sub>2</sub>/6063Al <i>In Situ</i> Composite Processed by Forge

Microstructural Evolution and Mechanical Properties of Friction Stir Processed ZrB2/6061Al Nanocomposites

Effects of (tib2 + ZrB2) Nanoparticles on Microstructure and Properties of 7055al Matrix Composites

Microstructure and mechanical performances of high strength ZTA/LaAl11O18 composites

Corrosion and wear performance and mechanism study of ZrB2/AA6016

Microstructure and Mechanical Properties of ZrB2–Nb Composite

High Strength and High Creep Resistant ZrB 2 /al Nanocomposites Fabricated by Ultrasonic-Chemical In-Situ Reaction

Serrated flow and ZrB2 nanoparticle agglomerations of in-situ AA6061 alloy matrix composites

Study on the Effect of Micromorphology and Creep Properties of In Situ (ZrB2 + Al2O3)/AA6016 Composites in Extruded State

Microstructure of ZrB2/6063Al In Situ Composite Processed by Forge