Abstract:Background Poor rotation of the femoral component in total knee arthroplasty (TKA) can result in various postoperative complications, underscoring the critical importance of preoperative planning. Purpose To improve the accuracy of femoral component positioning during TKA, this study compared the accuracy and repeatability of different two-dimensional (2D) computed tomography (CT) measurement methods for measuring the posterior condylar angle (PCA) in preoperative TKA planning. Methods A retrospective analysis was conducted on 75 patients (150 knees) who underwent bilateral lower extremity computed tomography angiography (CTA) at Fuyang People's Hospital from January 2021 to July 2021. Three different methods were used to measure the PCA based on 2D CT images (axial CT slices) and three-dimensional(3D) models (femoral models reconstructed from CT data) in this study. Method 1: Single-plane 2D CT measurement, measuring PCA in the most obvious single-plane CT slice of the surgical transepicondylar axis (sTEA); Method 2: multi-plane 2D CT measurement, identifying and locating anatomical landmarks in multiple 2D CT slices and measuring PCA; Method 3: 3D model measurement, measuring PCA in the reconstructed femur 3D model. Compare the differences in PCA measurements between the three measurement methods. A positive PCA measurement was recorded when the sTEA was externally rotated relative to the posterior condylar line (PCL). Any difference exceeding 3° between the PCA measurement in the 2D CT and the PCA reference value in the 3D model was classified as an outlier. The intraclass correlation coefficient (ICC) and Bland–Altman method were utilized to assess the intra- and inter-observer reproducibility of the three measurement methods. Results The PCA measurement in the single-plane 2D CT was 1.91 ± 1.94°, with a measurement error of − 1.22 ± 1.32° and 12.7% of outlier values. In the multi-plane 2D CT, the PCA measurement was 2.96 ± 1.68°, with a measurement error of -0.15 ± 0.91° and 6.0% of outlier values. The PCA measurement in the 3D model was 3.12 ± 1.69°. The PCA measurement in single-plane 2D CT was notably smaller than that in multi-plane 2D CT and 3D models, with no significant difference between the latter two. The multi-plane 2D CT showed significantly lower measurement error and outlier values than the single-plane 2D CT. All three PCA measurement methods exhibited high reproducibility (ICC: 0.93 ~ 0.97). Conclusions Using of multi-plane 2D CT for measuring PCA in preoperative planning of TKA has high reproducibility and accuracy, with fewer outlier values. We recommend preoperative measurement of PCA using muti-plane 2D CT to improve the accuracy of positioning the femoral component rotational alignment during surgery.

The Optimal Variation Range of Posterior Condylar Offset Associated with Positive Clinical Outcomes of Primary Total Knee Arthroplasty: A Retrospective Analysis.

Measurement of femoral posterior condylar offset and posterior tibial slope in normal knees based on 3D reconstruction

Significance of Posterior Condyle Offset in Total Knee Arthroplasty

The role of posterior condylar offset ratio on clinical and functional outcome of posterior stabilized total knee arthroplasty: a retrospective cohort study

Posterior condylar offset influences the intraoperative soft tissue balance during posterior-stabilized total knee arthroplasty

Posterior Condyle Offset and Maximum Knee Flexion Following a Cruciate Retaining Total Knee Arthroplasty.

Posterior femoral condylar offsets of a Chinese population.

Pre- and postoperative Coronal Plane Alignment of the Knee classification and its impact on clinical outcomes in total knee arthroplasty

Increased Posterior Condylar Offset Decreases the Extension Gap in Cases With Flexion Contracture in Modified Gap Technique Total Knee Arthroplasty

Preserving coronal knee alignment of the knee (CPAK) in unicompartmental knee arthroplasty correlates with superior patient-reported outcomes

Large variance in a lateral osteoarthritic population prior to and following lateral unicompartmental arthroplasty: An analysis of knee phenotypes

AutoCOR: Autonomous Condylar Offset Ratio Calculator on TKA-Postoperative Lateral Knee X-ray

Higher Pelvic Incidence Was Associated with a Higher Risk of Sagittal Malposition of Femoral Component and Poor Outcomes of Primary Total Knee Arthroplasty: A Retrospective Cohort Analysis.

The influence of implant factors on patient outcomes in primary total knee arthroplasty

Association Between Overhang of the Posterior Femoral Condyle and Restricted Postoperative Knee Flexion Related to Patient-Reported Stiffness in Medial-Pivot Total Knee Arthroplasty

Correlation study of the trans-epicondylar axis and femoral external rotation osteotomy in the total knee arthroplasty

Preoperative Joint Line Convergence Angle as an Indicator of Clinical Outcomes and Accuracy of Alignment Correction After Double-Level Osteotomy

Large multiplanar changes to native alignment have no apparent impact on clinical outcomes following total knee arthroplasty

Accuracy and Reproducibility of Two-Dimensional Computed Tomography-Based Positioning of Femoral Component Rotational Alignment in Preoperative Planning for Total Knee Arthroplasty

Asymmetry of Posterior Condyles in Resection Plane and Axial Curvature for Total Knee Arthroplasty

Effect of joint line orientation parameters on initial bone resection in mechanically aligned total knee arthroplasty: a retrospective clinicoradiological correlation study