Abstract:The impact of Zn on the mechanical properties and corrosion resistance of Al-Mg-Si alloys with high Cu contents was studied through microstructure analysis and accelerated corrosion testing. The age-hardening response of the alloy improved with the addition of trace Zn, and the poor corrosion resistance caused by high Cu content was overcome. Intergranular corrosion susceptibility (IGC) decreased and then increased with increasing Zn content. Al-Mg-Si-Cu alloys that contain 0.5 wt.% Zn possessed the best corrosion resistance. Zn decreased the potential difference between the matrix and the Al(Mn, Fe)Si phases according to scanning Kelvin probe force microscopy (SKPFM) tests, which reduced the driving force of corrosion in the alloy. Additionally, the addition of Zn promoted discontinuous precipitation at the grain boundaries, which was conducive to enhancing the IGC resistance. However, excessive Zn (1.0 wt.%) promoted the diffusion of more solute atoms near the grain boundaries to the grain boundaries, which coarsened the precipitated phase at the grain boundaries and shortened the interphase distance. Moreover, as the width of the PFZ increased, the concentration of solute atoms decreased, and the potential difference between the precipitated phase and the PFZ increased, leading to more severe IGC behavior. Therefore, an appropriate Zn content was beneficial for improving the corrosion properties and age-hardening response of Al-Mg-Si-Cu alloys.

Clarifying the Role of Quenching Conditions on Microstructure, Intergranular Corrosion Behavior and Mechanical Properties of Al-Mg-Si-Cu Alloy with High Cu

Effect of quenching protocols on microstructure and corrosion morphology in a recycled Al–Mg–Si alloy: Tracing Cu impurities

Effect of Quenching Rate on Microstructure, Mechanical and Corrosion Properties of Al-Zn-Mg-Cu-Cr-Zr Alloy

Effects of Cu Addition on the Microstructure and Properties of the Al–Mn–Fe–Si Alloy

Effects of Rapid Quenching on Grain Boundary Microstructure and Mechanical Properties of an Al-Mg-Si-Cu Alloy

Effect of Trace Zn on the Mechanical Properties and Corrosion Behavior of Al-Mg-Si Alloys with High Cu

Quantified effect of quench rate on the microstructures and mechanical properties of an Al–Mg–Si alloy

The effect of quenching rates on microstructure and mechanical properties of an Al-Si-Cu-Mg alloy

Correlations among stress corrosion cracking, grain-boundary microchemistry, and Zn content in high Zn-containing Al–Zn–Mg–Cu alloys

Effects of grain boundary chemistry and precipitate structure on intergranular corrosion in Al-Mg-Si alloys doped with Cu and Zn

Enhancing the intergranular corrosion resistance and mechanical properties of Al–Mg–xSi–Cu–Zn alloys by synergistic intergranular and intragranular precipitation behaviors

Effect of grain structures and precipitation characteristics on the corrosion behaviour of Sc-containing Al-Cu-Li alloy

Influence of Cu content on the hardenability of Al-xCu-1.1Li alloys

The role of copper in microstructure and toughness of intercritically reheated coarse grained heat affected zone in a high strength low alloy steel

Local corrosion mechanism of an Al-Zn-Mg-Cu alloy in oxygenated chloride solution: Cathode activity of quenching-induced η precipitates

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Influence of quenching rate on microstructure and dimensional stability of Al–Cu–Mg–Si alloy

Microstructure, mechanical properties and residual stress of high vacuum die casting AlSi10MgMn alloys with different spray quenching

Residual stress and precipitation of Mg-5Zn-3.5Sn-1Mn-0.5Ca-0.5Cu alloy with different quenching rates

Precipitation hardening and intergranular corrosion behavior of novel Al–Mg–Zn(-Cu) alloys