Abstract:Laser Powder Bed Fusion (L-PBF) provides great advantages in creating supersaturated solid solutions due to its intrinsic ultrafast cooling and high solidification rate, which is particularly desired for enhanced solid solution strengthening and precipitation strengthening. In the present work, a novel high strength Zr/Sc/Hf-modified Al-Mn-Mg alloy with a good L-PBF processability is investigated. The as-built alloy exhibits a heterogeneous microstructure featuring a bi-modal grain structure with coarse columnar and fine equiaxed grains and heterogeneously distributed nanometer and submicrometer-sized cuboid-shaped primary Al3(Sc,Zr,Hf) particles. The Al3(Sc,Zr,Hf) phase, exhibiting a homogeneous elemental distribution of Zr, Sc, and Hf, adopts a cubic L12 structure with a lattice parameter of 0.4044 ± 0.009 nm, showing a good coherency with α-Al. Additionally, the rapid L-PBF solidification enables the formation of submicrometer-sized elongated and globular primary Al6Mn and a supersaturated Al matrix with a high dislocation density. This results in a good combination of strength (yield strength of 438 ± 3 MPa and ultimate tensile strength of 504 ± 2 MPa) and ductility (elongation at fracture of 10.9 ± 1.4 %), with a moderate work hardening strength of 113 ± 12 MPa. Direct-ageing at 325 °C for 10 h promotes the formation of a large amount of rod-shaped Al6Mn precipitates and a few spherical Al3(Sc,Zr,Hf) nanoprecipitates. The heat treatment increases the hardness from 166 ± 2 HV in as-built condition to 173 ± 4 HV and enhances the tensile strength (yield strength of 487 ± 2 MPa and ultimate tensile strength of 542 ± 3 MPa) but slightly reduces the ductility to 7.4 ± 0.7 %. The high strength was achieved by the synergistic effect of grain boundary strengthening, solid solution strengthening, and Orowan strengthening mechanisms.

CALPHAD Aided Design of a Crack-Free Al-Mg-Si-Ti Alloy with High Strength: Heterogeneous Nucleation and Eutectic Filling During Additive Manufacturing

CALPHAD-aided design of high-strength Al-Si-Mg alloys for sufficient laser powder bed fusion processability

Facile and cost-effective approach to additively manufacture crack-free 7075 aluminum alloy by laser powder bed fusion

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Fabrication of Ti3Al-Based Intermetallic Alloy by Laser Powder Bed Fusion Using a Powder Mixture

A novel crack-free Ti-modified Al-Cu-Mg alloy designed for selective laser melting

Computational design of a crack-free aluminum alloy for additive manufacturing

Microstructure characterization and mechanical properties of crack-free Al-Cu-Mg-Y alloy fabricated by laser powder bed fusion

In situ design of ultrafine-grained 7075 Al alloy with laser powder bed fusion

Developing a high-strength Al-Mg-Si-Sc-Zr alloy for selective laser melting: Crack-inhibiting and multiple strengthening mechanisms

A Novel High-Strength Al-Li Alloy Printed by Laser Powder Bed Fusion: Microstructural Evolution and Strengthening Mechanism

Design of Low-Cost and High-Strength Titanium Alloys Using Pseudo-Spinodal Mechanism through Diffusion Couple Technology and CALPHAD

CALPHAD-guided design of Mg-Y-Al alloy with improved strength and ductility via regulating the LPSO phase

Development of a high strength Zr/Sc/Hf-modified Al-Mn-Mg alloy using Laser Powder Bed Fusion: Design of a heterogeneous microstructure incorporating synergistic multiple strengthening mechanisms

CALPHAD-guided Design and Experimental Study on a Novel Al-Ti-Nb Alloy

Toward additive manufactured crack-free NiTiCu shape memory alloys with low-hysteresis and tailorable phase transition behavior supported by theoretical design

Additive manufacturing of an ultrastrong, deformable Al alloy with nanoscale intermetallics

Selective laser melting additive manufacturing of 7xxx series Al-Zn-Mg-Cu alloy: Cracking elimination by co-incorporation of Si and TiB2

Novel approach to additively manufacture high-strength Al alloys by laser powder bed fusion through addition of hybrid grain refiners

Designing against phase and property heterogeneities in additively manufactured titanium alloys

Laser powder bed fusion of nano-titania modified 2219 aluminium alloy with superior mechanical properties at both room and elevated temperatures: The significant impact of solute