Abstract:The Mg96Y2Ni2 (at. %) alloy containing-50% volume fraction of long period stacking ordered (LPSO) phase was processed by extrusion and subsequent equal channel angular pressing (ECAP). A bimodal alpha-Mg matrix with different non-dynamic recrystallized (non-DRXed) proportions and a fully dynamic recrystallized (DRXed) matrix with different grain sizes were obtained by regulating extrusion and ECAP processing parameters, and the relationship between tensile properties and microstructure was investigated. The alloy extruded at 390 degrees C has high area ratio of non-DRXed regions with-35% and low area ratio of DRXed regions with-15%, as well as fine DRXed grains of-0.6 mu m, exhibiting ultrahigh tensile yield strength of 505 MPa and low elongation to failure of 3.5%. The alloy extruded at 450 degrees C exhibited bimodal microstructures containing non-DRXed grains with-13% and DRXed grains with-37%, and DRXed grains with the size of 2.1 mu m, exhibiting tensile yield strength of 400 MPa and elongation to failure of 10%. Fully recrystallized ultra-fine alpha-Mg grains with the size of-0.55 mu m was obtained after extrusion alloy was subjected to ECAP for 8 passes at 400 degrees C and subsequent 4 passes at 300 degrees C. The ultrafine-grained ECAPed alloy obtains tensile yield strength of 450 MPa and elongation to failure of 8%, exhibiting excellent strength-ductility balance. The lower TYS of the ECAPed alloy compared with the alloy extruded at 390 degrees C may be ascribed to the break of the LPSO phase into particles, which do not transfer load as effectively as long strips, as well as the fully DRXed grains with weak texture, which has less strengthening effect than that of the non-DRXed grains with strong basal texture. While the fully recrystallized ultra-fine Mg grains contribute to the increase of elongation to failure. This work provides theoretical guidance for develop of Mg-LPSO two-phase alloys with excellent strength-ductility synergy.

CALPHAD-guided design of Mg-Y-Al alloy with improved strength and ductility via regulating the LPSO phase

Tailoring the heterophase interfacial structures to improve both strength and ductility of Al-Li alloys by fine tuning major solute Mg

Enhanced strength and corrosion resistant of Mg-Gd-Y-Al alloys by LPSO phases with different Al content

Improved Strength in Wrought Mg–Y–Ni Alloys by Adjusting the Block-Shaped LPSO Phase and Plate-Shaped Γ′ Phase

Effects of Bulk LPSO Phases on Mechanical Properties and Fracture Behavior of As-Extruded Mg-Gd-Y-Zn-Zr Alloys

High Performance Mg Alloy with Designed Microstructure and Phases

Mechanistic investigation of a low-alloy Mg–Ca-based extrusion alloy with high strength–ductility synergy

Enhancing Strength-Ductility Synergy in an Extruded Al-Cu-Li-Mg-Ag Alloy Via Homogeneous GP Zones and Dislocation Configuration

Achieving ultra-strong Mg alloys via a novel hierarchical long-period stacking ordered architecture

Microstructure Evolution and Mechanical Properties of Mg-LPSO Two Phase Mg96Y2Ni2 (at. %) Alloy Processed by Hot Extrusion and Decreasing-Temperature ECAP

Towards development of a high-strength stainless Mg alloy with Al-assisted growth of passive film

CALPHAD-aided design of high-strength Al-Si-Mg alloys for sufficient laser powder bed fusion processability

Alloying design and microstructural control strategies towards developing Mg alloys with enhanced ductility

Enhancing strength and ductility of low-cost rare earth Mg-5Y-Ni alloy containing LPSO phase fabricated via multi-pass rolling based on dislocation regulation and grain refinement

New strategy to solve the ambient strength-ductility dilemma in precipitation-strengthened Mg-Gd alloys via Li addition

Enhanced Mechanical Properties of As-Cast Al-7.0Si-1.5Cu-xMg Alloys Through Synergistic Main Strengthening Phases by Controlling Mg Element

Toward strength-ductility synergy in Al–Mg alloys: augmenting solute Mg concentration and strain-hardening ability via melt spinning and hot extrusion

Achieving Enhanced Mechanical Properties of Extruded Mg-Gd-Y-Zn-Zr Alloy by Regulating the Initial LPSO Phases

Strength-ductility synergy in Mg98.3Y1.3Ni0.4 alloy processed by high temperature homogenization and rolling

Effect of Ca addition on microstructure and mechanical properties of Mg–3.8Al–1.1Sn alloys

High-modulus Magnesium Alloy: Control of Microstructure and Mechanical Properties Via In-Situ Synthesis of the Al2RE Phase