Abstract:The Mg96Y2Ni2 (at. %) alloy containing-50% volume fraction of long period stacking ordered (LPSO) phase was processed by extrusion and subsequent equal channel angular pressing (ECAP). A bimodal alpha-Mg matrix with different non-dynamic recrystallized (non-DRXed) proportions and a fully dynamic recrystallized (DRXed) matrix with different grain sizes were obtained by regulating extrusion and ECAP processing parameters, and the relationship between tensile properties and microstructure was investigated. The alloy extruded at 390 degrees C has high area ratio of non-DRXed regions with-35% and low area ratio of DRXed regions with-15%, as well as fine DRXed grains of-0.6 mu m, exhibiting ultrahigh tensile yield strength of 505 MPa and low elongation to failure of 3.5%. The alloy extruded at 450 degrees C exhibited bimodal microstructures containing non-DRXed grains with-13% and DRXed grains with-37%, and DRXed grains with the size of 2.1 mu m, exhibiting tensile yield strength of 400 MPa and elongation to failure of 10%. Fully recrystallized ultra-fine alpha-Mg grains with the size of-0.55 mu m was obtained after extrusion alloy was subjected to ECAP for 8 passes at 400 degrees C and subsequent 4 passes at 300 degrees C. The ultrafine-grained ECAPed alloy obtains tensile yield strength of 450 MPa and elongation to failure of 8%, exhibiting excellent strength-ductility balance. The lower TYS of the ECAPed alloy compared with the alloy extruded at 390 degrees C may be ascribed to the break of the LPSO phase into particles, which do not transfer load as effectively as long strips, as well as the fully DRXed grains with weak texture, which has less strengthening effect than that of the non-DRXed grains with strong basal texture. While the fully recrystallized ultra-fine Mg grains contribute to the increase of elongation to failure. This work provides theoretical guidance for develop of Mg-LPSO two-phase alloys with excellent strength-ductility synergy.

Enhancing strength and ductility of low-cost rare earth Mg-5Y-Ni alloy containing LPSO phase fabricated via multi-pass rolling based on dislocation regulation and grain refinement

Strength-ductility synergy in Mg98.3Y1.3Ni0.4 alloy processed by high temperature homogenization and rolling

Dissolution and Reprecipitation of 14H-LPSO Structure Accompanied by Dynamic Recrystallization in Hot-Extruded Mg89Y4Zn2Li5 Alloy

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Achieving enhanced mechanical properties in the Mg–Y–Zn–V alloy by refining grains and improving the morphology and distribution of LPSO via pre-forging and subsequent rolling

Deformation-induced Dynamic Precipitation of 14H-LPSO Structure and Its Effect on Dynamic Recrystallization in Hot-Extruded Mg-Y-Zn Alloys

Enhanced Mechanical Properties of Extruded Mg–Y–Zn Alloy Fabricated Via Low-Strain Rolling

Synergistically improved damping, elastic modulus and mechanical properties of rolled Mg-8Li-4Y–2Er-2Zn-0.6Zr alloy with twins and long-period stacking ordered phase

High Strain Rate Quasi-Superplasticity Behavior in an Ultralight Mg-9.55Li-2.92Al-0.027Y-0.026Mn Alloy Fabricated by Multidirectional Forging and Asymmetrical Rolling

Microstructure Evolution and Mechanical Properties of Mg-LPSO Two Phase Mg96Y2Ni2 (at. %) Alloy Processed by Hot Extrusion and Decreasing-Temperature ECAP

Improved Strength in Wrought Mg–Y–Ni Alloys by Adjusting the Block-Shaped LPSO Phase and Plate-Shaped Γ′ Phase

Effect of rolling deformation on microstructure and mechanical properties of Mg–Y–Nd–Al alloy

High-Strength β-Phase Magnesium-Lithium Alloy Prepared by Multidirectional Rolling

Microstructures and mechanical properties of high-strength Mg-Gd-Y-Zn-Zr alloy sheets processed by severe hot rolling

Non-basal Slips Mediated Dynamic Recrystallization Promote Synergistic Strengthening and Toughening of Centrifugal Casting Mg–1.1Mn–0.5Al Alloy via High Strain Rolling

Improving the mechanical properties of duplex Mg-Li-Zn alloy by mixed rolling processing

Revealing the Interaction Between Dislocations and LPSO-Precipitates Structure in a Mg-Y-Al Alloy at Different Temperatures

Reducing the yield asymmetry in Mg-5Li-3Al-2Zn alloy by hot-extrusion and multi-pass rolling

Effect of Rolling Strain on Microstructure and Tensile Properties of Dual-Phase Mg–8Li–3Al–2Zn–0.5Y Alloy

Achieving ultrahigh strength in binary Al-10Mg alloy through heavy cryogenic rolling

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy