Abstract:In this article, the drag characteristics of an underwater vehicle propelled by a synthetic jet (SJ) is numerically studied. The underwater vehicle studied is REMUS Autonomous underwater vehicle (AUV). The cruising speed studied is up to 10 knots. The actuation parameters of the SJ actuator are the same under different cruising speeds. When the SJ actuator works, the drag of the vehicle changes periodically. The SJ-induced additional pressure drag increases with increasing cruising speed. The additional friction force is negligible. The thrust of the actuator decreases with increasing cruising speed. The thrust outputted by the SJ actuator when used for underwater vehicle propulsion is smaller than the thrust of an isolated actuator. The mathematical model of the additional drag, the model of the thrust, and the velocity distribution is given to assist the analysis in this article. 1. Introduction The advance in propulsion technique is the key to the evolution of underwater robots. The most common method for underwater robot propulsion is using screw propellers. Thrust is generated through the high speed rotation of the blades. The fluid is accelerated not only in the axial direction but also in the radial direction; however, only fluid acceleration in the axial direction can generate thrust. A significant part of the energy is wasted in the radial direction without thrust generation. As a result, the efficiency of screw propellers is low. Furthermore, the protruded screw propellers induce significant added resistance. This further reduces the total hydrodynamic efficiency of the vehicle. Nature always inspires the technical revolution in engineering. In nature there exist many marine creatures such as squids adopting jet propulsion. The jet created by squids is called pulsed jet. On the other hand, the jet of screw propellers is called steady jet. Studies about pulsed jet showed that compared with the steady jet, pulsed jet possess higher propulsion efficiency (Krueger 2001; Krueger & Gharib 2003, 2005; Moslemi & Krueger 2010; Lydia et al. 2011; Robert & John 2013). Seikman (1963), Weihs (1977), and recently Krueger and Gharib (2003) have shown that pulsed jets can give rise to a greater average thrust than steady jets of an equivalent mass flow rate. Lydia A. Ruiz, Robert W. Whittlesey, and John O. Dabiri found through experiment that pulsed jet has a propulsion efficiency that is 40% higher than that of steady jet, and a drag-based hydrodynamic efficiency increase more than 70% (Lydia et al. 2011). The mechanism behind this high efficiency is the formation of the vortex. The vortex will induce a radial velocity gradient at the nozzle exit. The velocity distribution becomes more ununiform compared with steady jet. As a result, the pressure at the nozzle exit will increase. This is observed by Krueger through experiment.

Effect of Waterjet Propulsion on the Hydrodynamic Performance of Caterpillar Track Amphibious Vehicle

Design Method of Water Jet Pump Towards High Cavitation Performances

Bollard Pull and Self-Propulsion Performance of a Waterjet Propelled Tracked Amphibian

Design of Contra-Rotating Waterjet Pump Based on High Cavitation Performances

Analyzing the performance of hull and water jet propeller under mooring conditions: effects of shallow water depths and varying inflow speeds

Numerical Analysis on Self-Propulsion of a Waterjet-Propelled Ship with Different Propulsion Models

Experimental and Numerical Study on Influence of Wheel Attachments on Resistance Performance of Amphibious Vessel for Marine Debris Collection

Experimental and CFD investigation on resistance reduction of hydrofoils for amphibious vehicles

A Study on the Hydrodynamic Characteristics of a Synthetic Jet Propelled Underwater Vehicle

Numerical Simulation of the Horizontal Water-Entry Process of High-Speed Vehicles

Effect of Interaction of Flapping Hydrofoil Motion Parameters on Thrust Pulsation Performance

Research on the water and land motion performance of an amphibious vehicle

Optimal Design of Inlet Passage for Waterjet Propulsion System Based on Flow and Geometric Parameters

Influence of Inlet Duct Length on the Hydraulic Performance of the Waterjet Propulsion Device

Hydrodynamic Investigations of a Cross-Domain Vehicle with the Capability of High-Speed Cruising on Water Surface

Computational Analysis of the Effect of Hull Vane on Hydrodynamic Performance of a Medium-speed Vessel

Study on the Impact of Tail Wing Profiles on the Resistance Characteristics of Amphibious Vehicles

Velocity and Trajectory Tracking Control Model for Underactuated UUVs Through Coupling of Direct CFD and PID Control Algorithm

Hydrodynamic Design of an Advanced Submerged Propulsion

Effect of Tip Clearance on Hydraulic Performance of Water-jet Pump

Analysis of Ventilated Cavitation Around A Cylinder Vehicle with Nature Cavitation Using A New Simulation Method