Abstract:SO3 in coal-fired flue gas will cause equipment corrosion and the emission of sulfuric acid mist. The performance of injecting the alkaline adsorbent into the flue gas to remove SO3 is affected by the adsorption of SO2 in the flue gas. Taking Ca(OH)(2) as a typical alkaline adsorbent, a model describing the adsorption of SO3 and SO2 by Ca(OH)(2) particles was established, based on the combination of the product island-growth model and the grain model. The parameters in the model were determined by the experimental data of adsorption in the fixed-bed reactor. The adsorption process of a single Ca(OH)(2) particle was studied by numerical simulation. The adsorption of SO3 and SO2 was found to involve two stages: (1) In the early stage when there existed unreacted grain surface in the particle, SO3 and SO2 mainly reacted with the left fresh grain surface. The SO3 adsorption was controlled by internal pore diffusion and surface reaction, in which internal pore diffusion played a major role. The SO3 adsorption showed a shrinking core mode. The SO2 adsorption was controlled by internal pore diffusion and surface reaction and occurred throughout the entire particle. The SO3 adsorption selectivity at the outer surface of the particle was the highest, and decreased with a decreasing dimensionless particle radius R/R-0. (2) In the later stage when the grain surface was completely reacted, the SO3 adsorption was controlled by internal pore diffusion and product-layer diffusion, in which product-layer diffusion played a major role. The SO2 adsorption was controlled by product-layer diffusion. The product-layer diffusion coefficient in the SO3 adsorption process was significantly higher than that of the SO2 adsorption, so SO3 was still significantly adsorbed in the later stage. The adsorption process of Ca(OH)(2) under different particle structure parameters showed that decreasing the particle radius and increasing the particle porosity and specific surface area increased the SO3 removal efficiency as well as the total conversion of Ca(OH)(2). Decreasing the particle radius and the specific surface area and increasing the particle porosity increased the SO3 adsorption selectivity by Ca(OH)(2). When preparing industrial adsorbents, the optimization of the particle porous structure should be given attention. (C) 2021 Elsevier Ltd. All rights reserved.

Alkaline absorbents for SO2 and SO3 removal: A comprehensive review

Theoretical Model for SO3Removal from Flue Gas Using Alkali Sorbent Injection Technology in Power Plant

A review on sulfur trioxide (SO 3 ) removal from coal combustion process: Research progress challenges and suggestions

An Overview of Flue Gas SO 2 Capture Technology Based on Absorbent Evaluation and Process Intensification

SO 3 removal by submicron absorbents synthesized via inhibition method: The product layer grows like parallel peaks

So3 Removal by Submicron Absorbents Synthesized Via Inhibition Method: the Product Layer Grows Like Parallel Peaks

Sulfur Trioxide Removal Performance of Alkaline Sorbents Injection in the Temperature Range 400–705 °C: a Pilot‐scale Study

Experimental Study on the Removal of SO3 from Coal-Fired Flue Gas by Alkaline Sorbent

SO3 Removal from Flue Gas by Using Na2SO3

Process Analysis of SO3 Removal by Ca(OH)2 Particles from Flue Gas

Study on the competitive absorption between complex components in flue gas and SO3 by alkaline absorbent

Temperature Impact on SO2 Removal Efficiency by Ammonia Gas Scrubbing

Improving the removal of SO 3 aerosol by combining flue gas condensation and alkali spray

Recent advances in energy-efficient and regenerative SO2 absorption over deep eutectic solvents

Study on Competitive Absorption of SO3 and SO2 by Calcium Hydroxide

Absorption of SO2 from Flue Gas by Aqueous Fulvic Acid Solution

Absorption mechanism of SO3 on various alkaline absorbents in the presence of SO2

CHARACTERISTICS OF SULFURDIOXIDE ABSORPFION IN MULTI-COMPONENT SUSPENSIONS

Study on a Novel Semidry Flue Gas Desulfurization with Multifluid Alkaline Spray Generator

Review on Removal of SO2, NOx, Mercury, and Arsenic from Flue Gas Using Green Oxidation Absorption Technology

Chemical Absorption of SO2 by Using Ethylene Diamine/Phosphoric Acid Solution