Abstract:Abstract Ultrasonic-assisted chemical mechanical polishing (UA-CMP) can greatly improve the sapphire material removal and surface quality, but its polishing mechanism is still unclear. This paper proposed a novel model of material removal rate (MRR) to explore the mechanism of sapphire UA-CMP. It contains two modes, namely two-body wear and abrasive-impact. Furthermore, the atomic force microscopy (AFM) in-situ study, computational fluid dynamics (CFD) simulation, and polishing experiments were conducted to verify the model and reveal the polishing mechanism. In the AFM in-situ studies, the tip scratched the reaction layer on the sapphire surface. The pit with a 0.22 nm depth is the evidence of two-body wear. The CFD simulation showed that abrasives could be driven by the ultrasonic vibration to impact the sapphire surface at high frequencies. The maximum total velocity and the air volume fraction (AVF) in the central area increased from 0.26 to 0.55 m/s and 20% to 49%, respectively, with the rising amplitudes of 1–3 μm. However, the maximum total velocity rose slightly from 0.33 to 0.42 m/s, and the AVF was nearly unchanged under 40–80 r/min. It indicated that the ultrasonic energy has great effects on the abrasive-impact mode. The UA-CMP experimental results exhibited that there was 63.7% improvement in MRR when the polishing velocities rose from 40 to 80 r/min. The roughness of the polished sapphire surface was R a = 0.07 nm. It identified that the higher speed achieved greater MRR mainly through the two-body wear mode. This study is beneficial to further understanding the UA-CMP mechanism and promoting the development of UA-CMP technology.

Chemical-mechanical synergies effects of multi-purpose pH regulators on C-, A-, and R-plane sapphire polishing

Effect of Potassium Persulfate As an Additive on Chemical Mechanical Polishing Performance on C-, A- and R-Plane Sapphire

STUDY ON CHEMICAL MECHANICAL POLISHING OF R-PLANE SAPPHIRE BY DIFFERENT ADDITIVES

Research on the Polishing Performance of CMP Slurry for the Sapphire Crystal

Chemical mechanical polishing for sapphire wafers using a developed slurry

Chemical mechanical polishing (CMP) anisotropy in sapphire

Effect of Chloride Ions on the Chemical Mechanical Planarization Efficiency of Sapphire Substrate

Study on Chemical Mechanical Polishing Performances of Sapphire Wafer (0001) Using Silica-Based Slurry

AFM and XPS Studies on Material Removal Mechanism of Sapphire Wafer During Chemical Mechanical Polishing (CMP)

Study on the polishing performance and mechanism of sapphire wafers by different types of degradable surfactants

Effects of Slurry Ph on Chemical and Mechanical Actions During Chemical Mechanical Polishing of YAG

Highly Efficient Removal of Sapphire by Composite Nanoabrasive with Novel Inorganic Polyelectrolyte As a Binder

Novel model of material removal rate on ultrasonic-assisted chemical mechanical polishing for sapphire

Mechanism Exploration of the Effect of Polyamines on the Polishing Rate of Silicon Chemical Mechanical Polishing: A Study Combining Simulations and Experiments

Machining performance and material removal mechanism of sapphire with novel polishing slurry

Fe-Nx/C Assisted Chemical–mechanical Polishing for Improving the Removal Rate of Sapphire

Experimental Study of Ultrasonic Vibration Assisted Chemical Mechanical Polishing for Sapphire Substrate

Effect of the carboxyl group number of the complexing agent on polishing performance of alumina slurry in sapphire CMP

Preparation of Non-Spherical Silica Composite Abrasives by Lanthanum Ion-Induced Effect and Its Chemical–mechanical Polishing Properties on Sapphire Substrates

Tribochemical mechanisms of abrasives for SiC and sapphire substrates in nanoscale polishing

High Efficiency Chemical Mechanical Polishing for Silicon Wafers Using a Developed Slurry