Abstract:Striking a balance between the mechanical properties and electromagnetic interference shielding effectiveness (EMI SE) of Mg alloys stands as a critical concern within the realm of electronics and communications. This study endeavors to optimize the mechanical properties and EMI SE of Mg alloy sheets through a combination of extrusion and rolling (E-R). OM, SEM, XRD, EBSD, and TEM obtained the microstructures of Mg-6Zn-1Y-1La0.5Zr alloys under extrusion and different rolling strain treatments, and the effects of the microstructures on the mechanical properties and EMI SE were revealed. The microstructure of the as-extruded Mg-6Zn-1Y-1La-0.5Zr (abbreviated as ZKL611K) alloy exhibited a distinct bimodal microstructure, with refined dynamically recrystallized (DRXed) grains surrounding coarse unDRXed regions. Subsequent rolling treatments induced a decrease in the aspect ratio of the unDRXed regions, a rapid reduction of DRXed grains, and the accumulation of dislocations within the as-rolled alloy. Statistical analysis of mechanical properties and EMI SE revealed that an optimal balance in the sheets subjected to "extrusion + 37 % rolling reduction", yield strength (YS) of 319 MPa, ultimate tensile strength (UTS) of 375 MPa, and elongation of 12.3 %. Furthermore, the EMI SE ranged from 81 dB to 114 dB within the frequency range of 30-1500 MHz. However, further increments in rolling reduction adversely affected mechanical properties while improving EMI SE. The observed enhancement in mechanical properties can be primarily attributed to the synergistic effects of grain size, second phase, dislocations, low- angle grain boundaries (LAGBs), and texture. Meanwhile, the improved EMI SE can be mainly attributed to the diffuse distribution of the second phase at multiple scales and the modulation of the texture through E-R treatments.

Excellent Synergy of Formability and Strength of a Mg-Zn-Y-Ca-Zr Alloy by Tailoring Segregation-Assisted Weak Elliptical Ring Texture

Development of a Novel Strength Ductile Mg–7Al–5Zn Alloy with High Superplasticity Processed by Hard-Plate Rolling (HPR)

Developing High-Strength and Ductile Mg-Gd-Y-Zn-Zr Alloy Sheet Via Bimodal Grain Structure Coupling with Heterogeneously-Distributed Precipitates

Development of Weak-Textured and High-Performance Mg–Zn–Ca Alloy Sheets Based on Zn Content Optimization

Designing a low-alloyed Mg–Al–Sn–Ca alloy with high strength and extraordinary formability by regulating fine grains and unique texture

Synergization of Ductility and Yield Strength in a Dilute Quaternary Mg-Zn-Gd-Ca Alloy Through Texture Modification and Guinier–Preston Zone

Improving Formability of Mg–Ca–Zr Sheet Alloy by Microalloying of Zn

Development of High Strength and Formability Mg-6Zn-0.2Ca Alloy Via Multi-Pass Warm Rolling and Aging Treatment

Prominent Role of High-Volume Fraction Mg17Al12 Dynamic Precipitations on Multimodal Microstructure Formation and Strength-Ductility Synergy of Mg–Al–Zn Alloys Processed by Hard-Plate Rolling (HPR)

A rolled Mg−8Al−0.5Zn−0.8Ce alloy with high strength-ductility synergy via engineering high-density low angle boundaries

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Balancing the Strength and Ductility of Mg-6Zn-0.2Ca Alloy Via Sub-Rapid Solidification Combined with Hard-Plate Rolling

Achieving High Strength and High Ductility in Magnesium Alloy Using Hard-Plate Rolling (HPR) Process.

Achieving Superior Strength-Ductility Synergy in a Heterostructured Magnesium Alloy Via Low-Temperature Extrusion and Low-Temperature Annealing

Optimisation of Alloy Composition for Highly-Formable Magnesium Sheet

High strength-ductility synergy and low anisotropy of Mg-4.5Al-2.6Zn-0.3Mn alloy sheet achieved by annealing after rolling

Excellent Room-Temperature Ductility and Formability of Rolled Mg–Gd–Zn Alloy Sheets

Enhanced ductility and strength of Mg-1Zn-1Sn-0.3Y-0.2Ca alloy achieved by novel micro-texture design

Excellent Strength-Ductility Synergy Properties of Mg-Sn-Zn-Zr Alloy Mediated by a Novel Differential Thermal ECAP (DT-ECAP)

Achieving High Ductility in Hot-Rolled Mg-xZn-0.2Ca-0.2Ce Sheet by Zn Addition

Enhanced Mechanical Properties and Electromagnetic Interference Shielding Effectiveness in Mg-6Zn-1Y-1La-0.5Zr Alloy Sheet by Hot Deformation