Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Interface Diffusion and Reaction Mechanisms of Fe3O4–MgO System in Pellets under Different Atmospheres

New Insights on Consolidation Behavior of Fe2O3 in the Fe3O4-CaO-MgO-SiO2 System for Fluxed Pellet Production: Phase Transformations and Morphology Evolution

Diffusion and reaction mechanism of limestone and quartz in fluxed iron ore pellet roasting process

Evaluating the Effect of MgO/Al2O3 Ratio on Thermal Behaviors and Structures of Blast Furnace Slag with Low Carbon Consumption

Softening–Melting Behaviors of a MgO-SiO2-FeO Slag System on a Coke Bed

New understanding on formation mechanism of CaFe2O4 in Fe2O3 -Fe3O4-CaO-SiO2 system during sintering Process: Phase transformation and morphologies evolution

Relationship and Mechanism Analysis of Soft-Melt Dropping Properties and Primary-Slag Formation Behaviors of the Mixed Burden in Increasing Lump Ore Ratio

The Influence of FeO on the Reaction between Fe–Al–Ca Alloy and Al2O3–CaO–FeO Oxide during Heat Treatment at 1473 K

Mg2+ Diffusion-Induced Structural and Property Evolution in Epitaxial Fe3O4 Thin Films.

Preparation and Characterization of MnFe2O4 by a Microwave-Assisted Oxidative Roasting Process

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Effect of W(mgo)/w(al2o3) Ratio and Basicity on Microstructure and Metallurgical Properties of Blast Furnace Slag

Interfacial Phenomenon and Marangoni Convection of Fe–C Melt on Coke Substrate under in Situ Observation

Effect Of Magnesium Flux On Metallurgical Performance Of Pellets

Effect of CaO and MgO additives on the compressive strength of pellets: Exploration on the decisive stage during induration

Interfacial reaction behavior in blast furnace and analysis of influence mechanism

Structure and Reactivity of the Iron Oxide Specimen Supported on Magnesia Via Different Preparation Methods

Effect of MgO Addition on the Metallurgical Properties of the Vanadium-Titanium Pellet with Simulating Blast Furnace Conditions

Updating mechanism of siderite roasting through insights into reactions between inherent oxides of iron and carbon

Synthesis and Sintering Reaction Mechanism of High-Performance MgO-CaO-Fe2O3 Clinker

Melting–Dropping Property of Blast Furnace Charge on the Basis of its Slag Formation Behavior