Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Effect of Carbon Concentration on Melting Behavior of Steel Scraps in Hot Metal Baths

Numerical simulation on the melting kinetics of steel scrap in iron-carbon bath

Diffusive steel scrap melting in carbon-saturated hot metal—phenomenological investigation at the solid–liquid interface

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Wetting and Spreading Behavior of Molten Iron in Contact with Graphite Substrate: Interfacial Effects

Analyses and Calculation of Steel Scrap Melting in a Multifunctional Hot Metal Ladle

Influence of Carbon on the Microstructure Evolution and Hardness of Fe-13Cr-xC (x = 0-0.7 wt.%) Stainless Steel

Effect of Cooling Rates on the Local—Overall Morphology Characteristics of Solidification Structure at Different Stages for High Carbon Steel

Flow, Heat‐Transfer, and Mixing Behaviors of Scrap Steel in a Refining Ladle with Bottom Blowing

Analysis of the melting process of carbon-bearing pellets in iron bath, slag bath and graphite crucible

Effect of Cooling Rate on Microstructure and Mechanical Properties of a Microlaminated Low-Density Steel

Influences of Cooling Rates on Solidification and Segregation Characteristics of Fe-Cr-Ni-Mo-N Super Austenitic Stainless Steel

Effect of Carbon Partitioning Temperature on Microstructure and Mechanical Properties of Low Carbon Steel Containing Cu

Effect of Cooling Rate on the Grain Morphology and Element Segregation Behavior of Fe-Mn-Al-C Low-Density Steel During Solidification

Effect of Different Ultrasonic Treatments on Solidification Structure of High Carbon Liquid Steel

Equilibrium Concentration of Carbon in High-Carbon High-Alloy Steel During Carbon Partitioning Process

In situ observation and investigation of effect of cooling rate on slab surface microstructure evolution in microalloyed steel

Effect of electrical parameters and slag system on macrostructure of electroslag ingot

Investigation of Carbon Segregation During Low Temperature Tempering in a Medium Carbon Steel

Numerical and Experimental Study on Carbon Segregation in Shaped Billet of Medium Carbon Steel with Combined Electromagnetic Stirring.

Al Alloy Melting Behavior and Interfacial Reactions with Steel Under Natural Convection