Abstract:Steel scrap melting kinetics is a key factor that affects the scrap ratio and temperature trajectory of Basic Oxygen Furnace steelmaking process and the productivity and energy utilization of Electric Arc Furnace steelmaking process. In this paper, the interface between steel scrap and melt is analyzed and a novel theoretical model of steel scrap melting in iron-carbon bath is established. Moreover, the effects of bath temperature, bath carbon content, preheating temperature and characteristic length of steel scrap on the melting rate of steel scrap, mass transfer coefficient of carbon, heat transfer coefficient and interface carbon concentration were investigated. The results show that the ultimate steady melting rate increases from −2.04 × 10−4 to −3.32 × 10−3 m/s with the increases of bath temperature from 1793 K to 1873 K, the ultimate steady heat and mass transfer coefficient first increase and subsequently decrease, are in the range of 1.04 × 105 to 2.86 × 105 W/m2/K and 0 to 2.89 × 10−4 m/s, respectively. As the bath carbon content increase from 1.0 wt% to 4.0 wt%, the ultimate steady melting rate increases from −8.85 × 10−5 to −3.23 × 10−4 m/s, the ultimate steady heat transfer coefficient first increases and subsequently decreases, is in the range of 7.59 × 104 to 1.01 × 105 W/m2/K. Furthermore, the ultimate steady mass transfer coefficient and the ultimate steady interface carbon content gradually decreases from 1.40 × 10−4 to 5.21 × 10−5 m/s and from 0.73 to 0.69 wt%, respectively. With the increase of preheating temperature and characteristic length of steel scrap, the ultimate steady melting rate, heat transfer coefficient between steel scrap and melt, mass transfer coefficient and interface carbon concentration remain almost constant, about −8.85 × 10−5 m/s, 8.40 × 104 W/m2/K, 1.40 × 10−4 m/s and 0.70 wt%, respectively.

Analyses and Calculation of Steel Scrap Melting in a Multifunctional Hot Metal Ladle

Flow, Heat‐Transfer, and Mixing Behaviors of Scrap Steel in a Refining Ladle with Bottom Blowing

Numerical simulation on the melting kinetics of steel scrap in iron-carbon bath

Diffusive steel scrap melting in carbon-saturated hot metal—phenomenological investigation at the solid–liquid interface

Effect of Carbon Concentration on Melting Behavior of Steel Scraps in Hot Metal Baths

Mathematical modelling and techno-economic analysis of electric arc furnace steelmaking process with hot metal charging in China

Numerical analysis for the heat transfer behavior of steel ladle as the thermoelectric waste-heat source

Optimization of melting process of 50 t ultra-high electric arc furnace

Introduction of Steelmaking Process with Resource Recycling

Numerical Study on Heat Transfer Characteristic of Hot Metal Transportation before EAF Steelmaking Process

Saving Ladle Control Model of Steel Ladle in Steelworks

Study on Heat Transfer Process between High-Temperature Slag Particles and Scrap in Drum Based on DEM Method

Research of slagless steelmaking and technology control in converter

Technology of metallurgy for continuous scrap preheating electric arc furnace

Energy demand in secondary steel making process: numerical analysis to assess the influence of the ladle working lining properties

Enhanced numerical tool to evaluate steel ladle thermal losses

Numerical simulation on the multiphase flow and reoxidation of the molten steel in a two-strand tundish during ladle change

Three-Stage Method Energy–Mass Coupling High-Efficiency Utilization Process of High-Temperature Molten Steel Slag

Optimizing the Steel Ladle Thermal Management: Toward a Sustainable and Cost‐Effective Ladle Fleet Logistics

MODELING THE MELTING OF SCRAP METAL OF DIFFERENT DENSITY IN A BOF SMELTING

Numerical Investigation on Heat Transfer Efficiency from Gas to Scrap in Feeding System of 100 t Consteel Electric Arc Furnace