Abstract:This study presents a computational fluid dynamics (CFD) based approach to determine the optimal positioning for an atmospheric turbulence sensor on a rotary-wing uncrewed aerial vehicle (UAV) with X8 configuration. The vertical (zBF) and horizontal (xBF) distances of the sensor to the UAV center to reduce the effect of the propeller-induced flow are investigated by CFD simulations based on the k−ε turbulence model and the actuator disc theory. To ensure a realistic geometric design of the simulations, the tilt angles of a test UAV in flight were measured by flying the drone along a fixed pattern at different constant ground speeds. Based on those measurement results, a corresponding geometry domain was generated for the CFD simulations. Specific emphasis was given to the mesh construction followed by a sensitivity study on the mesh resolution to find a compromise between acceptable simulation accuracy and available computational resources. The final CFD simulations (twelve in total) were performed for four inflow conditions (2.5 m s−1, 5 m s−1, 7.5 m s−1 and 10 m s−1) and three payload configurations (15 kg, 20 kg and 25 kg) of the UAV. The results depend on the inflows and show that the most efficient way to reduce the influence of the propeller-induced flow is mounting the sensor upwind, pointing along the incoming flow direction at xBF varying between 0.46 and 1.66 D, and under the mean plane of the rotors at zBF between 0.01 and 0.7 D. Finally, results are then applied to the possible real-case scenario of a Foxtech D130 carrying a CSAT3B ultrasonic anemometer, that aims to sample wind with mean flows higher than 5 m s−1. The authors propose xBF=1.7 m and zBF=20 cm below the mean rotor plane as a feasible compromise between propeller-induced flow reduction and safety. These results will be used to improve the design of a novel drone-based atmospheric turbulence measurement system, which aims to combine accurate wind and turbulence measurements by a research-grade ultrasonic anemometer with the high mobility and flexibility of UAVs as sensor carriers.

In-Flight Airflow Measurements for a High Maneuverability Ornithopter

Data-Driven Method for Flow Sensing of Aerodynamic Parameters Using Distributed Pressure Measurements

Flow Structure around a Multicopter Drone: A Computational Fluid Dynamics Analysis for Sensor Placement Considerations

Sparse Flow Sensor Placement Optimization for Flight-by-Feel Control of 2D Airfoils

APPLICATION OF ULTRASONIC ANEMOMETER ARRAY TO FIELD MEASUREMENTS OF THE DOWNWASH FLOW OF AN AGRICULTURAL UNMANNED HELICOPTER

Extraction of a Weak Flow Field for a Multi-Rotor Unmanned Aerial Vehicle (UAV) Using High-Speed Background-Oriented Schlieren (BOS) Technology.

Anemometer For Detection Of Very Low Speed Air Flow With Three-Dimensional Directionality

Compact Sphere-Shaped Airflow Vector Sensor Based on MEMS Differential Pressure Sensors

3D printed feathers with embedded aerodynamic sensing

Combined hot-film anemometers for measuring flow speed vectors

Design and Validation of an Aerodynamics and Kinematics Measurement Platform for Flapping-Wing Robots

Artificial Hair Sensor Placement Optimization on Airfoils for Angle of Attack Prediction

Flexible Calorimetric Flow Sensor with Unprecedented Sensitivity and Directional Resolution for Multiple Flight Parameter Detection

Neural Network-Based Airflow Vector Sensor Using Multiple MEMS Differential Pressure Sensors

Fiber-optic Integrated Aerodynamic Three-Hole Vector Probe for High-Velocity Flow Field Measurement

Research on Flow Sensor System Integrated with Wing of Micro Air Vehicle

A High-speed Nature Laminar Flow Airfoil and Its Experimental Study in Wind Tunnel with Nonintrusive Measurement Technique

Rotary-wing drone-induced flow – comparison of simulations with lidar measurements

Low Observable Uncrewed Aerial Vehicle Wind Tunnel Model Design, Manufacturing, and Aerodynamic Characterization

Flexible Micro Flow Sensor for Micro Aerial Vehicles

Aircraft flight parameter detection based on a neural network using multiple hot-film flow speed sensors