Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Flash Sintering of Silicon Carbide at Room Temperature

Flash Sintering of High-Purity Alumina at Room Temperature

Preparation of Porous Si2N2O/SiC Ceramics by Microwave Sintering

Fabrication of SiC Foam Ceramics at a Low Sintering Temperature by Adding Fly Ash

A versatile defect engineering strategy for room-temperature flash sintering

Flash Sintering Of 8ysz Ceramics Under Ac Field

Study on the Performance for Silicon Carbide Ceramics by Hot-pressing Sintering

Preparation of porous SiC-ceramics by sol–gel and spark plasma sintering

Study on Micro-structure and Properties of Al2O3/SiC Ceramics by Pressureless Sintering in Air

Silicon Carbide/Polysilazane Composite: Effect of Temperature on the Densification, Phase, and Microstructure Evolution

Gas-discharge induced flash sintering of YSZ ceramics at room temperature

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Enhanced toughness and hardness at cryogenic temperatures of silicon carbide sintered by SPS

Investigation of the effect of pressure, sintering temperature and time on silicon carbide microstructure

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Low-temperature preparation of La0.9Ca0.1CrO3 semiconductor ceramics by flash sintering

Rapid and cost-effective fabrication of SiC from Si scrap through flash sintering

Low-temperature preparation of porous SiC ceramics using phosphoric acid as a pore-forming agent and a binder

Enhancing densification rate and the unusual 4H-SiC polytype stabilization in ultrafast high-temperature sintering of α-SiC

Fabrication, microstructure, and properties of SiC/Al4SiC4 multiphase ceramics via an in-situ formed liquid phase sintering

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride