Abstract:Solar energy is clean and abundant, and it has been considered as a green energy. Solar energy can be utilized by photovoltaics (PV) or concentrating solar power (CSP) generation. PV converts solar energy into electricity cost-effectively, but it is sensitive to environmental conditions, such as weather, and unable to utilize spectrum outside the spectral response range. In contrast, CSP is less sensitive to environment conditions, but more costly than PV. Their advantages can be combined by integrating PV and CSP into a beam-splitting photovoltaic-thermal (PV-T) hybrid system, which splits incident solar radiation and projects the photovoltaic spectrum onto solar cells and the rest to CSP. In this way, full spectrum of solar radiation can be utilized, and the overall conversion efficiency is enhanced by increasing the efficiency of solar cells and heat. The beam-splitting PV-T system has shown a great potential in solar energy production; however, few studies consider hybrid systems with the newly emerging perovskite solar cells. This paper reports a perovskite solar cell (PSC) with various bandgaps by replacing Iodine ion (I−) in FA1-xMAxPbI3 with Bromine ion (Br−) in different proportions. In addition, the spectral response ranges of PSC were adjusted to 300–700, 300–730, 300–780, 300–800 and 300–830 nm in external quantum efficiency (EQE) curves. We also analyzed the trends of photovoltaic properties of PSC, measured with solar simulator, validated with characterization of perovskite films. Furthermore, a beam-splitting PV-T system with PSC of different spectral response ranges was simulated and optimized using the experimental data. Results show that the beam-splitting PV-T system can achieve a theoretical solar-to-electric efficiency of 25.74%. This efficiency is higher than those of single CSP and single PSC, which are 23.97% and 17.27% respectively. The efficiency tends to decline with ratio of Br− increasing, because though the open-circuit voltage boosts and EQE remains unchanged, the declined quality of PSC reduces the fill factor, which is detrimental to the overall efficiency. Even though introducing Br− cannot increase the overall efficiency, the changed spectral response range brings about shift of the optimum cutoff wavelength, and the efficiency just slightly decreases with low ratio of Br− mixing, which is important for matching beam splitters in beam-splitting PV-T system.

Perovskite Solar Cells with Tunable Bandgaps for Beam-Spiltting Photovoltaic-Thermal System

Using perovskite solar cells with tunable bandgaps for beam-splitting photovoltaic-thermal System

Effects of beam splitting on photovoltaic properties of monocrystalline silicon, multicrystalline silicon, GaAs, and perovskite solar cells for hybrid utilization

Spectral Splitting As a Route to Promote Total Efficiency of Hybrid Photovoltaic Thermal with a Halide Perovskite Cell

Perovskite Solar Cell-Thermoelectric Tandem System with a High Efficiency of over 23%

2‐in‐1 Optimization for High Performance Semitransparent Perovskite Solar Cells

Full‐Spectral Response Perovskite Solar Cells Through Integration of MXene Modified Near‐Infrared Organic Heterojunction and Waveguide‐Structure Quantum‐Cutting Down‐Converter

A new full-spectrum solar power system based on perovskite solar cell and thermally regenerative electrochemical cycle: Influential mechanism and performance limit

Interfacial Energy Level Tuning for Efficient and Thermostable CsPbI2Br Perovskite Solar Cells

Progress in Full Spectrum Solar Energy Utilization by Spectral Beam Splitting Hybrid PV/T System

High-Efficiency CsPbI2Br Perovskite Solar Cells with over 83% Fill Factor by Synergistic Effects of a Multifunctional Additive.

Enhancing photovoltaic performance through solar radiation splitting: A beam splitter-assisted hybrid approach with 2-D tracking and PCM integration

Enhanced Efficiency and Stability of Wide‐Bandgap Perovskite Solar Cells Via Molecular Modification with Piperazinium Salt

2D/3D heterostructured CsPbI2Br solar cells: a choice for a monolithic all-perovskite tandem device

Phase-Stable Wide-Bandgap Perovskites for Four-Terminal Perovskite/Silicon Tandem Solar Cells with over 30% Efficiency.

A perovskite solar cell-photothermal-thermoelectric tandem system for enhanced solar energy utilization

High-performance CsPbI2Br perovskite solar cells based on excess CsBr and ultra thin MgF2 layer

Quantifying the Energy Losses in CsPbI 2 Br Perovskite Solar Cells with an Open-Circuit Voltage of up to 1.45 V

Intermediate‐Adduct‐Assisted Growth of Stable CsPbI 2 Br Inorganic Perovskite Films for High‐Efficiency Semitransparent Solar Cells

Perovskite‐Based Tandem Solar Cells: Get the Most Out of the Sun

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells