Abstract:Solar energy is clean and abundant, and it has been considered as a green energy. Solar energy can be utilized by photovoltaics (PV) or concentrating solar power (CSP) generation. PV converts solar energy into electricity cost-effectively, but it is sensitive to environmental conditions, such as weather, and unable to utilize spectrum outside the spectral response range. In contrast, CSP is less sensitive to environment conditions, but more costly than PV. Their advantages can be combined by integrating PV and CSP into a beam-splitting photovoltaic-thermal (PV-T) hybrid system, which splits incident solar radiation and projects the photovoltaic spectrum onto solar cells and the rest to CSP. In this way, full spectrum of solar radiation can be utilized, and the overall conversion efficiency is enhanced by increasing the efficiency of solar cells and heat. The beam-splitting PV-T system has shown a great potential in solar energy production; however, few studies consider hybrid systems with the newly emerging perovskite solar cells. This paper reports a perovskite solar cell (PSC) with various bandgaps by replacing Iodine ion (I−) in FA1-xMAxPbI3 with Bromine ion (Br−) in different proportions. In addition, the spectral response ranges of PSC were adjusted to 300–700, 300–730, 300–780, 300–800 and 300–830 nm in external quantum efficiency (EQE) curves. We also analyzed the trends of photovoltaic properties of PSC, measured with solar simulator, validated with characterization of perovskite films. Furthermore, a beam-splitting PV-T system with PSC of different spectral response ranges was simulated and optimized using the experimental data. Results show that the beam-splitting PV-T system can achieve a theoretical solar-to-electric efficiency of 25.74%. This efficiency is higher than those of single CSP and single PSC, which are 23.97% and 17.27% respectively. The efficiency tends to decline with ratio of Br− increasing, because though the open-circuit voltage boosts and EQE remains unchanged, the declined quality of PSC reduces the fill factor, which is detrimental to the overall efficiency. Even though introducing Br− cannot increase the overall efficiency, the changed spectral response range brings about shift of the optimum cutoff wavelength, and the efficiency just slightly decreases with low ratio of Br− mixing, which is important for matching beam splitters in beam-splitting PV-T system.

Four-Terminal Tandem Solar Cells Using CH3NH3PbBr3 by Spectrum Splitting

Perovskite/Colloidal Quantum Dot Tandem Solar Cells: Theoretical Modeling and Monolithic Structure

Toward high-efficiency solution-processed tandem solar cells

An efficient planar-heterojunction solar cell based on wide-bandgap CH3NH3PbI2.1Br0.9 perovskite film for tandem cell application.

Wide-Gap Perovskite Via Synergetic Surface Passivation and Its Application Toward Efficient Stacked Tandem Photovoltaics.

Two-Terminal Tandem Solar Cells based on Perovskite and Transition Metal Dichalcogenides

Synergistic Enhancement of Efficient Perovskite/Quantum Dot Tandem Solar Cells Based on Transparent Electrode and Band Alignment Engineering

Four‐Terminal Perovskite‐CdSeTe Tandem Solar Cells: From 25% toward 30% Power Conversion Efficiency and Beyond

Four-terminal perovskite/silicon tandem solar cell with integrated Mie-resonant spectral splitter metagrating

All-perovskite tandem solar cells with 3D/3D bilayer perovskite heterojunction

Device simulation and experimental validation of perovskite-cadmium telluride 4T tandem solar cell

Triple-halide wide–band gap perovskites with suppressed phase segregation for efficient tandems

Perovskite-perovskite tandem photovoltaics with optimized bandgaps

Perovskite Solar Cell-Thermoelectric Tandem System with a High Efficiency of over 23%

Triple-halide Wide-Bandgap Perovskites Tailored Via Facile Organic Halide Treatment for High-Performance Perovskite/cu(in,ga)se2 Tandem Solar Cells

Bifacial all-perovskite tandem solar cells

Theoretical Analysis of All‐Inorganic Wide Bandgap Perovskite /Sn‐Based Narrow Bandgap Perovskite Tandem Solar Cells

2D/3D Heterostructure for Semitransparent Perovskite Solar Cells with Engineered Bandgap Enables Efficiencies Exceeding 25% in Four‐Terminal Tandems with Silicon and CIGS

Computational design of high performance hybrid perovskite on silicon tandem solar cells

Phase-Stable Wide-Bandgap Perovskites for Four-Terminal Perovskite/Silicon Tandem Solar Cells with over 30% Efficiency.

Perovskite Solar Cells with Tunable Bandgaps for Beam-Spiltting Photovoltaic-Thermal System