Abstract:The need for 2219 aluminum alloy and 2195 Al–Li alloy dissimilar friction stir welding (FSW) arises as the conventional 2219Al alloy was gradually replaced by the novel 2195Al alloy in fabrication of fuel tanks. However, the systematic investigation about the effect of welding parameters and material positioning on the microstructure evolution and mechanical properties of dissimilar FSW 2219Al/2195Al joints is lacking. In the present study, 2219Al-T8/2195Al-T8 plates were subjected to FSW under rotation rates of 800–1200 rpm and welding speeds of 200–800 mm min −1 with placing 2219Al-T8 alloys on the advancing side (AS) and retreating side (RS), respectively. The results showed that sound FSW joints were obtained under all the welding conditions. Welding parameters and material positioning affected the joint strength and fracture failure behavior. The FSW thermal cycle resulted in low hardness zones (LHZs) on both the 2219Al-T8 and 2195Al-T8 sides. The LHZ on the 2219Al-T8 side, characterized by partial coarsening of θ ′ (Al 2 Cu) precipitates and dissolution of the residual precipitates, showed the minimum hardness in the entire FSW joints. When 2219Al-T8 alloy was placed on the AS, the LHZ on the 2219Al-T8 side experienced higher peak temperature, and therefore more dissolution of θ ′ than that on the RS, thereby obtaining higher tensile strength. The tensile strength of the FSW joints at room temperature and − 196 °C largely increased as the welding speed increased from 200 to 400 mm min −1 . The FSW joints presented much higher tensile strength at − 196 °C than that at room temperature under the identical welding parameters and material position. The FSW joints fractured along the LHZ on the 2219Al-T8 side during tension. For the bending testing, the up and down bending failure angles were about 91–117° and 88–109°, respectively, with the weak zone appearing in "S" line or HAZ on the 2195Al-T8 side.

Insight into the Tribocorrosion of Aa7050 Friction Stir Welding Joint

Microstructure, MAO Performance, Interfacial Characteristics and Corrosion Behavior of FSW Joint of Al-Mg-Sc Alloy

Improving the corrosion resistance of friction stir welding joint of 7050 Al alloy via optimizing the process route

Effect of Microstructure Evolution on Corrosion Behavior of Friction Stir Welded Joint for 2195-T8 Alloy

Microstructure, mechanical properties and corrosion of friction stir welded 6061 Aluminum Alloy

Microstructure and mechanical properties of friction stir welding joint of in-situ ZrB2/AA7085 composites

Microstructure, microhardness and mechanical behavior of dissimilar AA7075/AA6061 alloys under friction stir welding

Quantifying intergranular corrosion susceptibility in AA2098‐T351 weldments through friction stir welding

A study on the mechanical property and corrosion sensitivity of an AA5086 friction stir welded joint

Effect of friction stir repair welding on microstructure and corrosion properties of 2219-T8 Al alloy joints

Friction stir welding of a rapidly solidified thin-strip continuous cast AA5182 Al–Mg alloy: analysis of microstructure evolution, mechanical properties, and corrosion resistance

Parametric effect on microstructure evolution, grain size and mechanical behaviour of friction stir butt welding of AA6061-T6 alloy

Characterization and evaluation of stable localized corrosion in a 7075-T6 aluminum alloy FSW joint before and after anodizing treatment

Microstructure evolution of thermo-mechanically affected zone in dissimilar AA2024/7075 joint produced by friction stir welding

Microstructure, mechanical and fracture properties of friction stir welded 2195 Al-Li alloy joints

Numerical Simulation and Experimental Characterization of Friction Stir Welding on Thick Aluminum Alloy Aa2139-T8 Plates

Impact of friction stir welding parameters and Al2TiO5 reinforcement on the mechanical, wear, and corrosion performance of dissimilar welded aluminium composite joints

Corrosion Fatigue Fracture Characteristics of FSW 7075 Aluminum Alloy Joints

Microstructure Evolution and Mechanical Properties of Friction Stir Welded Al–Cu–Li Alloy

Precipitation-dependent corrosion analysis of heat treatable aluminum alloys via friction stir welding, a review

Dissimilar friction stir welding of 2219-T8 and 2195-T8 aluminum alloys: part I—microstructure evolution and mechanical properties