Abstract:Although fly ash foam concrete (FAFC) is lightweight, heat-retaining, and insulating, its application options are constrained by its weak construction and short lifespan. The effects of various dosage ratios of the foaming agent (i.e., hydrogen peroxide), silica fume, and polypropylene fiber on the dry density, compressive strength, thermal insulation performance, pore structure parameters, and durability of FAFC were analyzed in this study, which sought to address the issues of low strength and low durability of FAFC. According to the findings, there is a negative correlation between the amount of hydrogen peroxide (as the foaming agent) and compressive strength, and, as the silica fume and polypropylene fiber (PP fiber) content rise, the strength will initially rise and then fall. The distribution of pore sizes gradually shifts from being dominated by small pores to large pores as the amount of foaming agent increases, while the porosity and average pore size gradually decrease. When the hydrogen peroxide content is 5%, the pore shape factor is at its lowest. The pore size distribution was first dominated by a small pore size and thereafter by a large pore size when the silica fume and PP fiber concentration increased. Prior to increasing, the porosity, average pore size, and pore shape factor all decreased. Additionally, the impact of PP fiber on the freeze–thaw damage to FAFC was also investigated at the same time. The findings indicate that the freeze–thaw failure of FAFC is essentially frost heave failure of the pore wall. The use of PP fiber is crucial for enhancing FAFC's ability to withstand frost. The best frost resistance is achieved at 0.4% PP fiber content. In conclusion, the ideal ratio for overall performance was found to be 5% hydrogen peroxide content, 4% silica fume content, and 0.1% polypropylene fiber content. The results obtained could be applied in different fields, such as construction and sustainable materials, among others.

Reinforcement Effect of Fly Ash with Different Morphologies on Aluminum Foam Prepared Via Powder Metallurgy

Function of Grinding Fly Ash in Production of Aluminum Foam

Novel Mullite Ceramic Foams with High Porosity and Strength Using Only Fly Ash Hollow Spheres As Raw Material

Compressive Characteristics of Aluminum-Fly Ash Syntactic Foams Processed by Microwave Sintering

Fabrication and characterization of aluminum foam reinforced with nanostructured γ-Al2O3 via friction stir process for enhanced mechanical performance

Optimization of Cellular Structure of Aluminum Foams Produced by Powder Metallurgy Method

Effects of process parameters and alloy compositions on the pore structure of foamed aluminum

Preparation and mechanism of fly ash based composite fillers with different morphologies and its application in filling polyamide 6

Characterization of as-cast microstructure of aluminum foams by melt foaming method

Preparation and Compressive Performance of an A356 Matrix Syntactic Foam

Fabrication of Mg-Al Alloy Foam with Close-Cell Structure by Powder Metallurgy Approach and Its Mechanical Properties

Mechanical Response of the Fly Ash Cenospheres/polyurethane Syntactic Foams Fabricated Through Infiltration Process

Preparation Technology of Aluminum Foam Sandwich Panels by Powder Metallurgy and Optimization of Cellular Structure

Investigating the Mechanical and Durability Characteristics of Fly Ash Foam Concrete

High mechanical performance alumina-reinforced aluminum nanocomposite metal foam produced by powder metallurgy: fabrication, microstructure characterization, and mechanical properties

Foaming Behavior of Microsized Aluminum Foam Using Hot Rolling Precursor

Microstructure and Compressive Properties of Aluminum Foams Made by 6063 Aluminum Alloy and Pure Aluminum

Foamability and mechanical properties of in situ submicron MgAl2O4p/Al composite foams by ultrasonic method

Fabrication of Uniform and Rounded Closed-Cell Aluminum Foams Using Novel Foamable Precursor Particles (FPPs)

Preparation of aluminum foam sandwich with metallurgical bonding using friction stir welding

Synthesis of metakaolin-based geopolymer foamed materials using municipal solid waste incineration fly ash as a foaming agent