Abstract:All-inorganic cesium lead iodine perovskite materials (CsPbI3) have been widely studied and applied to PSCs because of their excellent thermo-chemical stability and suitable bandgap. However, CsPbI3 still faces the issue of phase transitions under humid conditions. In this study, cesium trimethylacetate (CsTa) organic cesium salt is employed as an additive in the CsPbI2.84Br0.16 film. The results show that CsTa can have multifunctional effects on CsPbI2.84Br0.16 perovskite stability. The steric hindrance blocking effect of Ta- anions can efficiently prevent the tilt of the [PbI6](4-) octahedrons to inhibit the phase transition process from the corner-shared perovskite to the edge-shared non-perovskite structure. The Ta- groups are firmly located at the X site of the perovskite structure, leading to an increase in the energy barrier for X-site vacancy generation (from 0.816 eV to 1.217 eV), which slows the phase transition process induced by lattice disorder. Meanwhile, the decrease in crystal grain size after adding CsTa is beneficial for perovskite phase stability due to the decreased surface Gibbs free energy of CsPbI2.84Br0.16 crystals. In addition, the reduced defect density brought about by the improved crystal quality is also favorable for increasing the energy barrier for the phase transition from the perovskite phase to the delta phase. Finally, a champion PCE of 16.59% can be achieved from the HPbI3-prepared PSCs with adding CsTa, which maintain 80.88% of the initial performance after more than 1200 hours in air (RH: similar to 20%). Meanwhile, both 0.1-CsTa and 0.2-CsTa PbI2-prepared PSCs deliver excellent stability and maintain above 80% of the initial PCE after nearly 2000 hours. Impressively, under a relatively high thermal/moisture (temperature: 80 degrees C/RH: similar to 80%) environment, the 0.2-CsTa devices can still retain 87.41% of the initial performance after 500 hours of storage.

Synthesis of Stable Cs-Rich FA-Cs Perovskite Solar Cells by Assistance of a Lewis Base Additive

Hot-substrate assisted deposition for Cs-rich α-Cs1-xFAxPbI2Br (0 ≤ x ≤ 0.4) films

Optimizing the Light-Humidity Stability of Formamidinium Halide Perovskites Through Intermediate Phase and Strain Stress Adjustment

Cs0.15FA0.85PbI3/CsxFA1 -Xpbi3 Core/Shell Heterostructure for Highly Stable and Efficient Perovskite Solar Cells

Lewis Acid–Base Adducts for Efficient and Stable Cesium‐Based Lead Iodide‐Rich Perovskite Solar Cells

Fabrication and Characterization of FA x Cs 1− x PbI 3 Polycrystal Perovskite Solar Cells

Bifunctional Lewis Base‐Assisted Fabrication of High‐Quality CsPbIBr2 Perovskite for Efficient and Stable Solar Cells

Over 24% efficient MA-free CsxFA1−xPbX3 perovskite solar cells

CsI Pre-Intercalation in the Inorganic Framework for Efficient and Stable FA 1- x Cs x PbI 3 (Cl) Perovskite Solar Cells.

High-Efficiency And Thermal/Moisture Stable Cspbi2.84br0.16 Inorganic Perovskite Solar Cells Enabled By A Multifunctional Cesium Trimethylacetate Organic Additive

Constructing CsPbBr3 Cluster Passivated‐Triple Cation Perovskite for Highly Efficient and Operationally Stable Solar Cells

Sequential Introduction of Cations Deriving Large-Grain Cs(X)Fa(1-X)Pbi(3) Thin Film for Planar Hybrid Solar Cells: Insight into Phase-Segregation and Thermal-Healing Behavior

High-quality All-Inorganic CsPbI2Br Thin Films Derived from Phase-Pure Intermediate for Efficient Wide-Bandgap Perovskite Solar Cells

Stable Cesium Formamidinium Lead Halide Perovskites: A Comparison of Photophysics and Phase Purity in Thin Films and Single Crystals

Efficiency Evaluation on Csx[NH2CH = NH2]1−xPb(I1−yBry)3/crystalline Silicon Tandem Solar Cells

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

Hydrophobic Organic Ammonium Halide Modification toward Highly Efficient and Stable CsPbI 2.25 Br 0.75 Solar Cell

Using 4‐Chlorobenzoic Acid Layer Toward Stable and Low‐Cost CsPbI 2 Br Perovskite Solar Cells

Enhancement of thermal stability for perovskite solar cells through cesium doping

Numerical Simulation and Optimization of Highly Stable and Efficient Lead-Free Perovskite FA1−xCsxSnI3-Based Solar Cells Using SCAPS

Phase transition induced recrystallization and low surface potential barrier leading to 10.91%-efficient CsPbBr3 perovskite solar cells