Abstract:A two-step time-to-digital converter (TDC) is designed for the high-precision time measurement of the DIRC-like TOF (DTOF) detector at the Super Tau-Charm Facility (STCF). Extending the measurement range by Nutt's method, the TDC clock cycle is interpolated with two voltage-controlled tapped delay lines (TDL) connected by a dual-slope time amplifier (TA). By amplifying the residue from the first-step TDL-based interpolation with the TA and measuring it with the second TDL, the TDC resolution is significantly improved to sub-gate delay. Since the residue is extracted by a new method without the need of TA duplication or delay insertion, the TDC power consumption and conversion time are effectively reduced. By adopting the improved TA circuit into the TDC with a high gain, adjustable output offsets, and good linearity, the TDC measurement precision is guaranteed. In addition, a new DLL structure is proposed to stabilize the TDL against process, voltage, and temperature (PVT) variations with less power consumption. Benefiting from the proposed residue extraction method and DLL structure, the TDC exhibits low power consumption. To verify the TDC design, a prototype chip with two TDC channels is fabricated in GlobalFoundries (GF) 180 nm CMOS technology for performance evaluation. With a system clock of 150 MHz, it has a resolution (LSB) of 16.5 ps and a maximum sample rate of 6 MS/s. The differential nonlinearity (DNL) error ranges from - 0.98 LSB to 0.87 LSB and the integral nonlinearity error (INL) ranges from- 4.21 LSB to 2.83 LSB. With a bin-by-bin calibration method, the measured TDC precision is 12.1 ps on average within the 0-20 ns time interval measurement range. In addition, the TDC has low temperature sensitivity and does not require recalibration within a 20 C-degrees temperature range. Each TDC channel consumes 434 mu W power at 1 MS/s sample rate. The test results confirm that the proposed TDC can achieve high precision with a moderate sample rate and low power consumption without highly scaled technologies, which can meet the requirements of the DTOF detector at STCF.

A 7.9 Ps Resolution, Multi-Event TDC Using an Ultra-Low Static Phase Error DLL and High Linearity Time Amplifier for Dtof Sensors

A Two-Step Time-to-Digital Converter with 5.6ps Resolution and 1 - 4255μs Measurement Range

A 50-Ps Gated VCRO-Based TDC with Compact Phase Interpolators for Flash LiDAR

A 12 Ps Precision Two-Step Time-to-Digital Converter Consuming 434 $\mu$ W at 1 MS/s in 180 Nm CMOS with a Dual-Slope Time Amplifier

A 49.5 Μw Multichannel Time-to-Digital Converter with 2D/3D Imaging Fusion for APD LiDAR Sensors

A Sub-10ps Resolution Multichannel Time-to-Digital Converter with Two-Stage Interpolation for High-Energy Physics Applications

A 13-Bit, 12-ps Resolution Vernier Time-to-Digital Converter Based on Dual Delay-Rings for SPAD Image Sensor

A 10b, 0.7ps resolution coarse-fine time-to-digital converter in 65nm CMOS using a time residue amplifier

A 8bits, 6.2ps Resolution Two-Step Time-to-digital Converter with Set-Reset-based Arbiters and Signal Tracking Mechanism

A Time-to-digital Converter Used in Photon-Counting LIDAR

A High Resolution Time-to-Digital Converter (TDC) Based on Self-Calibrated Digital-to-Time Converter (DTC).

Development of a High Performance Digital Silicon Photomultiplier (dSiPM) for ToF PET Imaging

A high precision TDC based on a multi-phase clock

Picosecond Timing Electronics for a DIRC-Like Detector at the Super Tau-Charm Facility

Low-cost FPGA-based multi-channel TDC with high resolution and density for time-of-flight detectors

Optimized Design of A Tof Laser Range Finder Based on Time-Correlated Single Photon Counting

Photonic-Assisted Time-Interleaved Adc Based on Optical Delay Line

A 1.3mW 8-bit Two-step Time-to-Digital Converter

A Low Power Tdc With 0.5ps Resolution For Adpll In 40nm Cmos

A Time-to-Amplitude Converter With High Impedance Switch Topology for Single-Photon Time-of-Flight Measurement

A 12bit 39ps Two-Step Time-to-Digital Converter in 40nm CMOS