Abstract:Abstract Chemical-looping combustion (CLC) is a combustion process with inherent separation of carbon dioxide (CO 2 ), which is achieved by oxidizing the fuel with a solid oxygen carrier rather than with air. As fuel and combustion air are never mixed, no gas separation is necessary and, consequently, there is no direct cost or energy penalty for the separation of gases. The most common form of design of chemical-looping combustion systems uses circulating fluidized beds, which is an established and widely spread technology. Experiments were conducted in two different laboratory-scale CLC reactors with continuous fuel feeding and nominal fuel inputs of 300 W th and 10 kW th , respectively. As an oxygen carrier material, ground steel converter slag from the Linz–Donawitz process was used. This material is the second largest flow in an integrated steel mill and it is available in huge quantities, for which there is currently limited demand. Steel converter slag consists mainly of oxides of calcium (Ca), magnesium (Mg), iron (Fe), silicon (Si), and manganese (Mn). In the 300 W unit, chemical-looping combustion experiments were conducted with model fuels syngas (50 vol% hydrogen (H 2 ) in carbon monoxide (CO)) and methane (CH 4 ) at varied reactor temperature, fuel input, and oxygen-carrier circulation. Further, the ability of the oxygen-carrier material to release oxygen to the gas phase was investigated. In the 10 kW unit, the fuels used for combustion tests were steam-exploded pellets and wood char. The purpose of these experiments was to study more realistic biomass fuels and to assess the lifetime of the slag when employed as oxygen carrier. In addition, chemical-looping gasification was investigated in the 10 kW unit using both steam-exploded pellets and regular wood pellets as fuels. In the 300 W unit, up to 99.9% of syngas conversion was achieved at 280 kg/MW th and 900 °C, while the highest conversion achieved with methane was 60% at 280 kg/MW th and 950 °C. The material’s ability to release oxygen to the gas phase, i.e., CLOU property, was developed during the initial hours with fuel operation and the activated material released 1–2 vol% of O 2 into a flow of argon between 850 and 950 °C. The material’s initial low density decreased somewhat during CLC operation. In the 10 kW, CO 2 yields of 75–82% were achieved with all three fuels tested in CLC conditions, while carbon leakage was very low in most cases, i.e., below 1%. With wood char as fuel, at a fuel input of 1.8 kW th , a CO 2 yield of 92% could be achieved. The carbon fraction of C 2 -species was usually below 2.5% and no C 3 -species were detected. During chemical-looping gasification investigation a raw gas was produced that contained mostly H 2 . The oxygen carrier lifetime was estimated to be about 110–170 h. However, due to its high availability and potentially low cost, this type of slag could be suitable for large-scale operation. The study also includes a discussion on the potential advantages of this technology over other technologies available for Bio-Energy Carbon Capture and Storage, BECCS. Furthermore, the paper calls for the use of adequate policy instruments to foster the development of this kind of technologies, with great potential for cost reduction but presently without commercial application because of lack of incentives.

Plasma Chemical Looping: Unlocking High-Efficiency CO2 Conversion to Clean CO at Mild Temperatures

Inhibiting Recombination to Improve the Performance of Plasma-Based CO2 Conversion

Boosting the Conversion of CO2 with Biochar to Clean CO in an Atmospheric Plasmatron: A Synergy of Plasma Chemistry and Thermochemistry

Highly effective CO 2 splitting in a plasma-assisted membrane reactor

Advancing CO2 to CO conversion: Detailed impact analysis of atmospheric molecules in an ultrashort pulse laser filament plasma reactor

Low-Temperature Chemical Looping Combustion for Removing Unburnt Gaseous Components with A Cement-Supported Cuo Oxygen Carrier

Disentangling metallic cobalt sites and oxygen vacancy effects in synergistic plasma-catalytic CO2/CH4 conversion into oxygenates

Review of chemical looping technology for energy conservation and utilization: CO2 capture and energy cascade utilization

Chemical looping approaches to decarbonization via CO2 repurposing

Plasma-Assisted Chemical Looping Oxidative Coupling of Methane over LaMnO 3 at 400 °C

CO2-free conversion of CH4 to syngas using chemical looping

CO 2 conversion by plasma: how to get efficient CO 2 conversion and high energy efficiency

Investigation of Highly Efficient CO2 Hydrogenation at Ambient Conditions Using Dielectric Barrier Discharge Plasma

H2 production from a plasma-assisted chemical looping system from the partial oxidation of CH4 at mild temperatures

High-Purity Hydrogen Obtained via a Plasma-Assisted Chemical Looping Process Using Perovskite-Supported Iron Oxides as Oxygen Carriers

Efficient CO 2 to CO Conversion at Moderate Temperatures Enabled by the Cobalt and Copper Co-Doped Ferrite Oxygen Carrier

Analysis of Thermally Coupled Chemical Looping Combustion-Based Power Plants with Carbon Capture

Plasma‐Driven Efficient Conversion of CO2 and H2O into Pure Syngas with Controllable Wide H2/CO Ratios over Metal‐Organic Frameworks Featuring In Situ Evolved Ligand Defects

Chemical looping co-conversion of CH4 and CO2 using Fe2O3/Al2O3 pellets as both oxygen carrier and catalyst in a fluidized bed reactor

Avoiding CO2 capture effort and cost for negative CO2 emissions using industrial waste in chemical-looping combustion/gasification of biomass

Techno-economic analysis of chemical looping air separation using a perovskite oxide sorbent