Abstract:SiBCN ceramic has already been widely used in the thermal insulation field. To further enhance their mechanical properties in high-temperature environments, the preparation of SiBCN and ZrB2 based pyrolytic carbon (PyC) modified carbon fiber reinforced composite, i.e., 2D Cf/SiBCN-ZrB2, was proposed in this study. By using five cycles of polymer impregnation and pyrolysis (PIP), the composite could be synthesized with a high flexural strength at room temperature, i.e., 275 f 15 MPa. To understand the evolution of the microstructure caused by high temperatures and their influences on the mechanical properties, the composite samples were heat treated at 1200, 1400, 1600, and 1800 degrees C for 2 h, respectively. Comparing the flexural strengths of the samples before and after the heat treatments, and meanwhile combining the advanced microstructural characterizations, it was found that the composite was stable when the treating temperature was below 1400 degrees C, i.e., the flexural strength was 250 f 15 MPa with a strength retention rate of over 90 %. However, once the temperature was above 1600 degrees C, due to the crystallization of SiBCN-ZrB2 matrix, the pyrolysis of PyC interfaces, the carbothermal reduction reaction and the erosion of carbon fibers, the mechanical properties of the composite would reduce to 74 f 9 MPa. This study provides a new method for preparing 2D Cf/SiBCN-ZrB2, which reduces the number of PIP cycles of composite materials and enables rapid prototyping of composite materials. Additionally, this research can help materials scientists understand the mechanical properties of 2D Cf/SiBCN-ZrB2 composite materials in high-temperature environments and the evolution of their microstructure, identifying the range of application temperatures for 2D Cf/SiBCN-ZrB2.

Fracture Toughness Evolution and Failure Mechanisms of Two-Dimensional SiCf/SiC Composites at Temperatures Up to 1500 °C in Air

Tensile Properties of Two-Dimensional Carbon Fiber Reinforced Silicon Carbide Composites at Temperatures Up to 1800 °C in Air

Tensile Properties of Two-Dimensional Carbon Fiber Reinforced Silicon Carbide Composites at Temperatures Up to 2300 °C

High-temperature tensile behavior of 3D SiC/SiC composites

Insights into Fracture Mechanisms and Strength Behaviors of Two-Dimensional Carbon Fiber Reinforced Silicon Carbide Composites at Elevated Temperatures

Ultrahigh-temperature Mechanical Behavior and Failure Mechanisms of SiCf/SiC Composites

Mechanical Behavior of 2D C/SiC Composites at Elevated Temperatures under Uniaxial Compression

An Investigation of Dynamic Failure Progress and Properties of 2D C/SiC Composite from 173 K to 1273 K by SHTB

Tensile Mechanical Behavior and Failure Mechanism of a Plain-Woven SiCf/SiC Composites at Room and Elevated Temperatures

Experimental Study of High-Temperature Tensile Mechanical Properties of 3D Needled C/C–SiC Composites

High temperature bending properties and failure mechanism of 3D needled C/SiC composites up to 2000 °C

Analysis of the Fracture Behavior and Mechanism of PIP-C/SiC Composites at High Temperatures

Influence of thermo-exposure at high temperature of flexural behaviors of 3D-C/SiC composite

Compressive Strength and Damage Mechanisms of 2D-C/sic Composites at High Temperatures

Tensile Fatigue of a 2.5D-C/sic Composite at Room Temperature and 900°C

Mechanical Behaviors of C/SiC Composites Subjected to Uniaxial Compression at High Temperatures and High Strain Rates

Microstructure Evolution and Failure Mechanism of 2D Cf/SiBCN-ZrB2 F /Sibcn-Zrb 2 Composite at Elevated Temperatures

Mechanical properties and microstructure evolution of 3D C f /SiBCN composites at elevated temperatures

Tensile Properties of 2D-C/sic Composites at Temperatures Up to 1873 K at Wide-Ranging Strain Rates

The Dynamic Tensile Properties of 2D-C/sic Composites at Elevated Temperatures

Microstructure Evolution and Failure Mechanism of 2D Cf/SiBCN–ZrB2 Composite at Elevated Temperatures