Abstract:Introduction: The cervical spine, pivotal for mobility and overall body function, can be affected by cervical spondylosis, a major contributor to neural disorders. Prevalent in both general and military populations, especially among pilots, cervical spondylosis induces pain and limits spinal capabilities. Anterior Cervical Discectomy and Fusion (ACDF) surgery, proposed by Cloward in the 1950s, is a promising solution for restoring natural cervical curvature. The study objective was to investigate the impacts of ACDF implant design on postsurgical cervical biomechanics and neurorehabilitation outcomes by utilizing a biofield head-neck finite element (FE) platform that can facilitate scenario-specific perturbations of neck muscle activations. This study addresses the critical need to enhance computational models, specifically FE modeling, for ACDF implant design. Materials and methods: We utilized a validated head-neck FE model to investigate spine-implant biomechanical interactions. An S-shaped dynamic cage incorporating titanium (Ti) and polyetheretherketone (PEEK) materials was modeled at the C4/C5 level. The loading conditions were carefully designed to mimic helmet-to-helmet impact in American football, providing a realistic and challenging scenario. The analysis included intervertebral joint motion, disk pressure, and implant von Mises stress. Results: The PEEK implant demonstrated an increased motion in flexion and lateral bending at the contiguous spinal (C4/C5) level. In flexion, the Ti implant showed a modest 5% difference under 0% activation conditions, while PEEK exhibited a more substantial 14% difference. In bending, PEEK showed a 24% difference under 0% activation conditions, contrasting with Ti's 17%. The inclusion of the head resulted in an average increase of 18% in neck angle and 14% in C4/C5 angle. Disk pressure was influenced by implant material, muscle activation level, and the presence of the head. Polyetheretherketone exhibited lower stress values at all intervertebral disc levels, with a significant effect at the C6/C7 levels. Muscle activation level significantly influenced disk stress at all levels, with higher activation yielding higher stress. Titanium implant consistently showed higher disk stress values than PEEK, with an orders-of-magnitude difference in von Mises stress. Excluding the head significantly affected disk and implant stress, emphasizing its importance in accurate implant performance simulation. Conclusions: This study emphasized the use of a biofidelic head-neck model to assess ACDF implant designs. Our results indicated that including neck muscles and head structures improves biomechanical outcome measures. Furthermore, unlike Ti implants, our findings showed that PEEK implants maintain neck motion at the affected level and reduce disk stresses. Practitioners can use this information to enhance postsurgery outcomes and reduce the likelihood of secondary surgeries. Therefore, this study makes an important contribution to computational biomechanics and implant design domains by advancing computational modeling and theoretical knowledge on ACDF-spine interaction dynamics.

Impact of instrumentation material on local recurrence: a case-matched series using carbon fiber-PEEK vs. titanium

Carbon fiber-reinforced PEEK spinal implants for primary and metastatic spine tumors: a systematic review on implant complications and radiotherapy benefits

Use of MRI for postoperative RT planning in patients with CFR-PEEK instrumentation

Composite PEEK/Carbon fiber implants can increase the effectiveness of radiotherapy in the management of spine tumors

Clinical performance of implanted devices used in surgical treatment of patients with spinal tumors: a systematic review

The use of carbon fiber/polyetheretherketone (CF/PEEK) in pedicle screw fixation for spinal neoplasms-potential advantages in postoperative imaging and radiotherapy planning

Carbon Instrumentation in Patients with Metastatic Spinal Cord Compression

Biomechanical analysis of stabilization for thoracolumbar anterior spinal failure caused by osteolytic lesions, a finite element comparison of direct lateral corpectomy and posterior long segment instrumentation

Customized Multilevel 3D Printing Implant for Reconstructing Spine Tumor: A Retrospective Case Series Study in a Single Center

Robotic assisted surgery for the treatment of spinal metastases: A case series

Risk Factors for Instrumentation Failure after Total En Bloc Spondylectomy of Thoracic and Lumbar Spine Tumors Using Titanium Mesh Cage for Anterior Reconstruction

First Clinical Experience with a Carbon Fibre Reinforced PEEK Composite Plating System for Anterior Cervical Discectomy and Fusion

Design and 3D printing of novel titanium spine rods with lower flexural modulus and stiffness profile with optimised imaging compatibility

Implant Design and Cervical Spinal Biomechanics and Neurorehabilitation: A Finite Element Investigation

Complications of patients with bone tumors treated with carbon-fiber plates: an international multicenter study

Titanium Cages versus Polyetheretherketone Cages in Interbody Fusions: A Meta-Analysis of Clinical and Radiographic Outcomes

Medium Term Outcomes in Palliative Transpedicular Corpectomy with Cement Based Anterior Vertebral Reconstruction Performed for Patients with Spinal Metastasis

Comparison of different CT metal artifact reduction strategies for standard titanium and carbon‐fiber reinforced polymer implants in sheep cadavers

Minimally Invasive Spine Metastatic Tumor Resection and Stabilization: New Technology Yield Improved Outcome

Radiotherapy and Surgical Advances in the Treatment of Metastatic Spine Tumors: A Narrative Review

Evaluation of computed tomography artefacts of carbon-fiber and titanium implants in patients with spinal oligometastatic disease undergoing stereotactic ablative radiotherapy