Abstract:BACKGROUND CONTEXT : With the aging population, osteoporosis, which leads to poor fusion, has become a common challenge for lumbar surgery. In addition, most people with osteoporosis are elderly individuals with poor surgical tolerance, and poor bone quality can also weaken the stability of internal fixation. PURPOSE : This study compared the fixation strength of the bilateral traditional trajectory screw structure (TT-TT), the bilateral cortical bone trajectory screw structure (CBT-CBT), and the hybrid CBT-TT (CBT screws at the cranial level and TT screws at the caudal level) structure under different bone mineral density conditions. STUDY DESIGN : A finite element (FE) analysis study. METHODS Above all, we established a healthy adult lumbar spine model. Second, under normal and osteoporotic conditions, three transforaminal lumbar interbody fusion (TLIF) models were established: bilateral traditional trajectory (TT-TT) screw fixation, bilateral cortical bone trajectory (CBT-CBT) screw fixation, and hybrid cortical bone trajectory screw and traditional trajectory screw (CBT-TT) fixation. Finally, a 500-N compression load with a torque of 10 N/m was applied to simulate flexion, extension, lateral bending, and axial rotation. We compared the range of motion (ROM), adjacent disc stress, cage stress, and posterior fixation stress of the different fusion models. RESULTS : Under different bone mineral density conditions, the range of motion of the fusion segment was significantly reduced. Compared to normal bone conditions, the ROM of the L4-L5 segment, the stress of the adjacent intervertebral disc, the surface stress of the cage, and the maximum stress of the posterior fixation system were all increased in osteoporosis. Under most loads, the ROM and surface stress of the cage and the maximum stress of the posterior fixation system of the TT-TT structure are the lowest under normal bone mineral density conditions. However, under osteoporotic conditions, the fixation strength of the CBT-CBT and CBT-TT structures are higher than that of the TT-TT structures under certain load conditions. At the same time, the surface stress of the intervertebral fusion cage and the maximum stress of the posterior fixation system for the two structures are lower than those of the TT-TT structure. CONCLUSION : Under normal bone mineral density conditions, transforaminal lumbar interbody fusion combined with TT-TT fixation provides the best biomechanictability. However, under osteoporotic conditions, CBT-CBT and CBT-TT structures have higher fixed strength compared to TT-TT structures. The hybrid CBT-TT structure exhibits advantages in minimal trauma and fixation strength. Therefore, this seems to be an alternative fixation method for patients with osteoporosis and degenerative spinal diseases. CLINICAL SIGNIFICANCE This study provides biomechanical support for the clinical application of hybrid CBT-TT structure for osteoporotic patients undergoing TLIF surgery.

Biomechanical analysis of stabilization for thoracolumbar anterior spinal failure caused by osteolytic lesions, a finite element comparison of direct lateral corpectomy and posterior long segment instrumentation

Posterior spinal stabilization: A biomechanical comparison of Laminar Hook Fusion to a Pedicle Screw System

Stability Evaluation of Different Oblique Lumbar Interbody Fusion Constructs in Normal and Osteoporotic Condition – A Finite Element Based Study

Biomechanical Finite Element Analysis of Vertebral Column Resection and Posterior Unilateral Vertebral Resection and Reconstruction Osteotomy.

Biomechanical Effect of Different Posterior Fixation Techniques on Stability and Adjacent Segment Degeneration in Treating Thoracolumbar Burst Fracture With Osteoporosis: A Finite Element Analysis

Biomechanical characterization of vertebral body replacement in situ: Effects of different fixation strategies

The Effect of Rod Pattern, Outrigger, and Multiple Screw-Rod Constructs for Surgical Stabilization of the 3-Column Destabilized Cervical Spine - A Biomechanical Analysis and Introduction of a Novel Technique

Finite Element Analysis of Stability of Internal Fixation Reconstruction Methods for Lumbar Total Vertebral Resection

Evaluation of S2 Alar and Traditional S1 Pedicle Fixation for Severe Lumbar Spondylolisthesis in Different Bone Mineral Densities: a Finite Element Analysis

Biomechanical Evaluation and the Assisted 3D Printed Model in the Patient-Specific Preoperative Planning for Thoracic Spinal Tuberculosis: A Finite Element Analysis

Treatment of Old Vertebral Compression Fracture With Kyphosis by Different Reconstruction Methods: a Finite Element Analysis

Biomechanical Analysis of Spinal Reconstruction after Total En Bloc Spondylectomy for Lower Lumbar Spine

A finite element analysis on comparing the stability of different posterior fixation methods for thoracic total en bloc spondylectomy

Effets biomécaniques de la vertébroplastie dans les fractures thoraco-lombaires explosées traitées par ostéosynthèse trans-pédiculaire : une analyse par modèle d’éléments finis

Biomechanical influence of the surgical approaches, implant length and density in stabilizing ankylosing spondylitis cervical spine fracture

Biomechanical evaluation of lumbar spondylolysis repair with various fixation options: A finite element analysis

Biomechanical Assessment of Different Transforaminal Lumbar Interbody Fusion Constructs in Normal and Osteoporotic Condition-A Finite Element Analysis

Biomechanical Evaluation Of Two Endoscopic Spine Surgery Methods For Treating Lumbar Disc Herniation: A Finite Element Studies

Biomechanical effect of the extent of vertebral body fracture on the thoracolumbar spine with pedicle screw fixation: an in vitro study.

Biomechanical Comparison of Stand-Alone and Bilateral Pedicle Screw Fixation for Oblique Lumbar Interbody Fusion Surgery-A Finite Element Analysis