[ECG before administration of Ritalin®: Is it useful ?]

É. Aries,F. El Louali,C. Ovaert

DOI: https://doi.org/10.1016/j.arcped.2017.04.018

IF: 1.82

Archives de Pédiatrie

Abstract:

What problem does this paper attempt to address?

The biomechanical study of a modified lumbar interbody fusion-crenel lateral interbody fusion (CLIF): a three-dimensional finite-element analysis.

Yun-Lin Chen,Ou-Jie Lai,Yang Wang,Wei-Hu Ma,Qi-Xin Chen

DOI: https://doi.org/10.1080/10255842.2020.1745784

2020-01-01

Abstract:To analyze the biomechanical stability of a redesigned cage, a new lateral plate and the effect of length of cage in CLIF, an L4-L5 finite element model was performed. Six different internal fixation methods were designed and operated under six conditions (Stand-alone CLIF; CLIF with unilateral pedicle screws (CLIF + UPS); CLIF with bilateral pedicle screws (CLIF + BPS); CLIF with lateral plate (CLIF + LP); CLIF with lateral plate and unilateral pedicle screws (CLIF + LP + UPS); CLIF with lateral plate and bilateral pedicle screws (CLIF + LP + BPS)). Ranges of motion (ROM) and stress distribution were evaluated. The effect of the length of cage was analyzed. The ROMs of stand-alone CLIF group and other internal fixation groups were decreased by >90% compared with the intact group. The CLIF + LP + BPS group has the minimum ROM. The CLIF + LP group has smaller ROM than stand-alone group. The stand-alone group has the minimum stress except for extension condition. The CLIF + LP model has less ROM, but a greater stress load was observed in the lateral plate. As for the length of cage, the largest stress is located at the junction between cage and distal end plate, especially in the epiphyseal ring and cortical compact. We conduct a new 'cylinder wall theory' that the cage should be placed to cover the epiphyseal ring. We recommend the length of cage should cover the epiphyseal ring to reduce the subsidence of cage.
Biomechanical study of oblique lumbar interbody fusion (OLIF) augmented with different types of instrumentation: a finite element analysis

Xin-Yi Cai,Han-Ming Bian,Chao Chen,Xin-Long Ma,Qiang Yang

DOI: https://doi.org/10.1186/s13018-022-03143-z

IF: 2.6

2022-05-15

Journal of Orthopaedic Surgery and Research

Abstract:Background To explore the biomechanical differences in oblique lumbar interbody fusion (OLIF) augmented by different types of instrumentation. Methods A three-dimensional nonlinear finite element (FE) model of an intact L3-S1 lumbar spine was built and validated. The intact model was modified to develop five OLIF surgery models (Stand-alone OLIF; OLIF with lateral plate fixation [OLIF + LPF]; OLIF with unilateral pedicle screws fixation [OLIF + UPSF]; OLIF with bilateral pedicle screws fixation [OLIF + BPSF]; OLIF with translaminar facet joint fixation + unilateral pedicle screws fixation [OLIF + TFJF + UPSF]) in which the surgical segment was L4–L5. Under a follower load of 500 N, a 7.5-Nm moment was applied to all lumbar spine models to calculate the range of motion (ROM), equivalent stress peak of fixation instruments (ESPFI), equivalent stress peak of cage (ESPC), equivalent stress peak of cortical endplate (ESPCE), and equivalent stress average value of cancellous bone (ESAVCB). Results Compared with the intact model, the ROM of the L4–L5 segment in each OLIF surgery model decreased by > 80%. The ROM values of adjacent segments were not significantly different. The ESPFI, ESPC, and ESPCE values of the OLIF + BPSF model were smaller than those of the other OLIF surgery models. The ESAVCB value of the normal lumbar model was less than the ESAVCB values of all OLIF surgical models. In most postures, the ESPFI, ESPCE, and ESAVCB values of the OLIF + LPF model were the largest. The ESPC was higher in the Stand-alone OLIF model than in the other OLIF models. The stresses of several important components of the OLIF + UPSF and OLIF + TFJF + UPSF models were between those of the OLIF + LPF and OLIF + BPSF models. Conclusions Our biomechanical FE analysis indicated the greater ability of OLIF + BPSF to retain lumbar stability, resist cage subsidence, and maintain disc height. Therefore, in the augmentation of OLIF, bilateral pedicle screws fixation may be the best approach.

orthopedics
Oblique Lateral Interbody Fusion Combined With Lateral Plate Fixation for the Treatment of Lumbar Degenerative Diseases: a Preliminary Clinical Study

Hai-dong Li,Shi-Tong Xing,Ji-Kang Min,Xiang-Qian Fang,Shun-Wu Fan

DOI: https://doi.org/10.21203/rs.3.rs-836768/v1

2021-01-01

Abstract:Abstract Background The oblique lateral interbody fusion (OLIF) is a minimally invasive indirect decompression technique for the treatment of lumar spine disease. The OLIF has usually combined with supplemental posterior pedicle screw fixation for decreasing the perioperative complications. The purpose of this study was to evaluate clinical efficacy and complications of oblique lateral interbody fusion (OLIF) combined with lateral plate instrumentation for the treatment of lumbar degenerative diseases.Methods From May 2020 to August 2020, the clinical data of 20 patients who underwent OLIF combined with lateral plate instrumentation were retrospectively analyzed. The operation time, blood loss, and the complications were recorded. Also, the radiological parameters, Visual Analog Scale (VAS) score and Oswestry Disability Index (ODI) were evaluated before and after surgery.Results The average operation time, blood loss, and length of hospital stay were 75.41±11.53 min, 39.57±9.22 ml, and 7.22±1.85 days, respectively. The VAS and ODI had both significantly improved after surgery (7.23±1.26 VS 2.15±0.87; 60.27±7.91 VS 21.80±6.32, P < 0.001). The postoperative disk height (DH) was 13.02±8.83 mm, which is much higher than before (P < 0.001); The postoperative foraminal height (FH) improved significantly (16.18±3.49 VS 21.54±2.12 mm, P < 0.01), and the cross-sectional area (CSA) had improved from 88.95±14.79 mm2 to 126.53±8.83 mm2 (P < 0.001). The radiological fusion rate was 95% at the last follow-up, while cage subsidence was found in one case. No major complications, such as ureteral injury, vascular injury and vertebral body fracture occurred.Conclusions OLIF combined with lateral plate fixation can avoid the lumbar posterior surgery, minimize the operation time, blood loss and the posterior ligament complex disruption. It can realize one-stage intervertebral fusion and instrumentation through a single small incision.
Oblique Lateral Interbody Fusion Combined With Different Internal Fixations in The Treatment of Degenerative Lumbar Spine Disease: A Finite Element Analysis

ShuYi Zhang,Zhengpeng Liu,Chenshui Lu,Li Zhao,Chao Feng,Yahui Wang,Yilong Zhang

DOI: https://doi.org/10.21203/rs.3.rs-991669/v1

2021-11-10

Abstract:Abstract Little is known about the biomechanical performance of various internal fixations in oblique lumbar interbody fusion (OLIF). In this study, finite element (FE) analysis was used to describe the biomechanical findings of various different internal fixations to compare and explore the stability of each fixation. METHODS: Six validated FE models of the L3-S1 segment were reconstructed from computed tomography images, including (1) an intact model, (2)a stand-alone (SA) model with no instrument (3) a unilateral pedicle screw model (UPS), (4) a unilateral pedicle screw contralateral translaminar facet screw model (UPS-CTLFS), (5) a bilateral pedicle screw (BPS) model, and (6) a cortical bone trajectory screw (CBT).Three-dimensional model was performed by computed tomography data, and 150N static force and 10N.m moments in different directions were applied to the models to analyze the validation of the models in comparison with previous studies. Models of the OLIF cage was created with three-dimensional scanning to improve the accuracy of the FE analysis. Range of motion (ROM) of the surgical segment stresses, stress of the cage, and stress of fixation were evaluated in the different models. RESULTS: ROM increased from least to greatest as follows: BPS, UPS-CTFS, CBT, UPS, SA. The SA group had the greatest ROM and the SA group had the greatest ROM and stresses on the CAGE. The ROM of the BPS and UPS-CTFS was not significantly different for all motion loadings. Compared with the other three models, the BPS model had lower stresses in internal fixation for all loading conditions and the CBT screw internal fixation had the highest stresses for different loads Compared with the other groups. CONCLUSIONS The BPS model provided the best biomechanical stability for OLIF. The SA model was relatively less stable. The UPS-CFTS group reduced the ROM of the fusion segments, but the stresses on the internal fixation and CAGE were relatively higher in the UPS-CFTS Compared with the BPS group; and the CBT group had lower ROM in flexion and extension Compared with the BPS, but its ROM in rotation and lateral flexion was relatively higher. The stability of the CBT was poorer than that of the BPS and LPS-CTFS groups. The stress on the CAGE and internal fixation was greater in the CBT group.
Oblique lateral interbody fusion combined with different internal fixations for the treatment of degenerative lumbar spine disease: a finite element analysis

Shuyi Zhang,Zhengpeng Liu,Chenshui Lu,Li Zhao,Chao Feng,Yahui Wang,Yilong Zhang

DOI: https://doi.org/10.1186/s12891-022-05150-x

IF: 2.562

2022-03-04

BMC Musculoskeletal Disorders

Abstract:Abstract Background Little is known about the biomechanical performance of different internal fixations in oblique lumbar interbody fusion (OLIF). Here, finite element (FE) analysis was used to describe the biomechanics of various internal fixations and compare and explore the stability of each fixation. Methods CT scans of a patient with lumbar degenerative disease were performed, and the l3-S1 model was constructed using relevant software. The other five FE models were constructed by simulating the model operation and adding different related implants, including (1) an intact model, (2) a stand-alone (SA) model with no instrument, (3) a unilateral pedicle screw model (UPS), (4) a unilateral pedicle screw contralateral translaminar facet screw model (UPS-CTFS), (5) a bilateral pedicle screw (BPS) model, and (6) a cortical bone trajectory screw model (CBT). Various motion loads were set by FE software to simulate lumbar vertebral activity. The software was also used to extract the range of motion (ROM) of the surgical segment, CAGE and fixation stress in the different models. Results The SA group had the greatest ROM and CAGE stress. The ROM of the BPS and UPS-CTFS was not significantly different among motion loadings. Compared with the other three models, the BPS model had lower internal fixation stress among loading conditions, and the CBT screw internal fixation had the highest stress among loads. Conclusions The BPS model provided the best biomechanical stability for OLIF. The SA model was relatively less stable. The UPS-CTFS group had reduced ROM in the fusion segments, but the stresses on the internal fixation and CAGE were relatively higher in the than in the BPS group; the CBT group had a lower flexion and extension ROM and higher rotation and lateral flexion ROM than the BPS group. The stability of the CBT group was poorer than that of the BPS and LPS-CTFS groups. The CAGE and internal fixation stress was greater in the CBT group.

orthopedics,rheumatology
Biomechanical stability of oblique lateral interbody fusion combined with four types of internal fixations: finite element analysis

Jiayu Hao,XianSheng Tang,Nizhou Jiang,Hong Wang,Jian Jiang

DOI: https://doi.org/10.3389/fbioe.2023.1260693

IF: 5.7

2023-09-25

Frontiers in Bioengineering and Biotechnology

Abstract:Objective: Using finite element analysis to identify the optimal internal fixation method for oblique lateral lumbar interbody fusion (OLIF), providing guidance for clinical practice. Methods: A finite element model of the L4 – L5 segment was created. Five types of internal fixations were simulated in the generated L4-L5 finite element (FE) model. Then, six loading scenarios, i.e., flexion, extension, left-leaning, right-leaning, rotate left, and rotate right, were simulated in the FE models with different types of fixations. The biomechanical stability of the spinal segment after different fixations was investigated. Results: Regarding the range of motion (ROM) of the fused segment, OLIF + Bilateral Pedicle Screws (BPS) has a maximum ROM of 1.82° during backward bending and the smallest ROM in all directions of motion compared with other models. In terms of the von Mises stress distribution on the cage, the average stress on every motion direction of OLIF + BPS is about 17.08MPa, and of OLIF + Unilateral Vertebral Screw - Pedicle Screw (UVS-PS) is about 19.29 MPa. As for the von Mises stress distribution on the internal fixation, OLIF + BPS has the maximum internal fixator stress in left rotation (31.85 MPa) and OLIF + Unilateral Pedicle Screw (UPS) has the maximum internal fixator stress in posterior extension (76.59 MPa). The data of these two models were smaller than those of other models. Conclusion: OLIF + BPS provides the greatest biomechanical stability, OLIF + UPS has adequate biomechanical stability, OLIF + UVS-PS is inferior to OLIF + UPS synthetically, and OLIF + Double row vertical screw (DRVS) and Individual OLIF (IO) do not present significant obvious advantages.

multidisciplinary sciences
Biomechanical Evaluation of Anterolateral Screw Fixation for Oblique Lumbar Interbody Fusion Surgery – A Finite Element Analysis

gufang Fang,SG Chen,wda zhuang,WH Huang,Hongxun Sang

DOI: https://doi.org/10.21203/rs.3.rs-71475/v1

2020-10-09

Abstract:Abstract Background: The most common complication of oblique lumbar interbody fusion (OLIF) is cage subsidence. OLIF combined with internal fixation could help decrease the cage subsidence and increase the fusion rate. The aim of this study was to evaluate the biomechanical feasibility and safety in the patients undergoing OLIF surgery with anterolateral screw fixation (ASF). Methods : Based on our previous validated model , L4-L5 functional surgical models corresponding to the ASF and Bilateral pedicle screw fixation(BPSF) methods were created. A 500 N compression force was applied to the superior surface of the model to represent the upper body weight, and a 7.5 Nm moment was applied to simulate the six movement directions of the lumbar spinal model: flexion/extension, right/left lateral bending and right/left axial rotation. Finite element (FE) models were developed to compare the biomechanics of the ASF and BPSF groups. Results : Compared to the range of motion (ROM) of the intact lumbar model, that of the ASF model was decreased by 82.0% in flexion, 60.0% in extension, and the BPSF model was decreased by 86.7% in flexion, 77.3% in extension. Compared to the BPSF model, the maximum stresses of the L4 inferior endplate (IEP) and L5 superior endplate (SEP) were greatly increased in the ASF model; The contact surface between vertebrae and screw (CSVS) in the ASF model produced nearly100% more stresses than the BPSF model in all moment . Conclusions : OLIF surgery with ASF could not reduce the maximum stresses on the endplate and CSVS, which may be a potential risk factor for cage subsidence and screw loosening.
An in vitro biomechanical evaluation of integrated lateral plate combined with oblique lateral interbody fusion in different bone conditions

Zhiqiang Wang,Wanzhong Yang,Xiaoyin Liu,Simin Liang,Zecheng Cai,Wei Guo,Jianqun Zhang,Zhaohui Ge

DOI: https://doi.org/10.1038/s41598-024-80631-8

IF: 4.6

2024-11-29

Scientific Reports

Abstract:Oblique lateral interbody fusion (OLIF) is a minimally invasive surgery for the treatment of lumbar degenerative diseases (LDD). Under normal bone mass(NB), supplemental with lateral plate (LP) fixation has been proven to provide stability and reduce complications. However, it is unclear whether OLIF combined with LP fixation can achieve satisfactory fixation effects in cases of osteoporosis(OP) or osteopenia (OS)? In this study, Eighteen L3-5 spinal specimens from 3 to 6 months old fresh calves were equally divided into 3 groups: group A (NB), group B (OS) and group C (OP). A load control scheme was adopted and evaluated using multidirectional nondestructive moments (± 7.5 N·m). An electronic universal tester and a tensile/torsion tester were simulated to generate 6 degrees of freedom of motion, and a VIC-3D three-dimensional optical full-field strain measurement system dynamically tracked the surgical segmental displacement. Each spine was evaluated under the following conditions at the L4-5 level: intact (INT); OLIF stand-alone (SA); cage supplemented with LP, cage supplemented with unilateral pedicle screws (UPS), and cage supplemented with bilateral pedicle screws (BPS). The current data show that With NB and OS models, LP fixation significantly reduced ROM in the LB and AR directions, with slightly less stability than BPS fixation and comparable to UPS. In the case of OP, LP fixation may increase the risk of internal fixation failure, and it is more preferable to choose BPS fixation with stronger stability.

multidisciplinary sciences
Stability Evaluation of Different Oblique Lumbar Interbody Fusion Constructs in Normal and Osteoporotic Condition – A Finite Element Based Study

Ferenc Bereczki,Mate Turbucz,Rita Kiss,Peter Endre Eltes,Aron Lazary

DOI: https://doi.org/10.3389/fbioe.2021.749914

IF: 5.7

2021-11-05

Frontiers in Bioengineering and Biotechnology

Abstract:Introduction: In developed countries, the age structure of the population is currently undergoing an upward shift, resulting a decrease in general bone quality and surgical durability. Over the past decade, oblique lumbar interbody fusion (OLIF) has been globally accepted as a minimally invasive surgical technique. There are several stabilization options available for OLIF cage fixation such as self-anchored stand-alone (SSA), lateral plate-screw (LPS), and bilateral pedicle screw (BPS) systems. The constructs’ stability are crucial for the immediate and long-term success of the surgery. The aim of this study is to investigate the biomechanical effect of the aforementioned constructs, using finite element analysis with different bone qualities (osteoporotic and normal). Method: A bi-segmental (L2–L4) finite element (FE) model was created, using a CT scan of a 24-year-old healthy male. After the FE model validation, CAD geometries of the implants were inserted into the L3–L4 motion segment during a virtual surgery. For the simulations, a 150 N follower load was applied on the models, then 10 Nm of torque was used in six general directions (flexion, extension, right/left bending, and right/left rotation), with different bone material properties. Results: The smallest segmental (L3–L4) ROM (range of motion) was observed in the BPS system, except for right bending. Osteoporosis increased ROMs in all constructs, especially in the LPS system (right bending increase: 140.26%). Osteoporosis also increased the caudal displacement of the implanted cage in all models (healthy bone: 0.06 ± 0.03 mm, osteoporosis: 0.106 ± 0.07 mm), particularly with right bending, where the displacement doubled in SSA and LPS constructs. The displacement of the screws inside the L4 vertebra increased by 59% on average (59.33 ± 21.53%) due to osteoporosis (100% in LPS, rotation). BPS-L4 screw displacements were the least affected by osteoporosis. Conclusions: The investigated constructs provide different levels of stability to the spine depending on the quality of the bone, which can affect the outcome of the surgery. In our model, the BPS system was found to be the most stable construct in osteoporosis. The presented model, after further development, has the potential to help the surgeon in planning a particular spinal surgery by adjusting the stabilization type to the patient’s bone quality.

multidisciplinary sciences
Biomechanical Evaluation of an Oblique Lateral Locking Plate System for Oblique Lumbar Interbody Fusion: A Finite Element Analysis

Yinge Wang,Jiajia Wang,Sha Tu,Shuang Li,Jiangpu Yi,Haien Zhao,Huanhuan Qiao,Kang Yan,Bo Liao

DOI: https://doi.org/10.1016/j.wneu.2021.12.105

Abstract:Objective: The oblique lateral locking plate system (OLLPS) is a novel internal fixation with a locking and reverse pedicle track screw configuration designed for oblique lumbar interbody fusion (OLIF). The OLLPS is placed in a single position through the oblique lateral surgical corridor to reduce operative time and complications associated with prolonged anesthesia and prone positioning. The purpose of this study was to verify the biomechanical effect of the OLLPS. Methods: An intact finite element model of L1-S1 (intact) was established based on computed tomography images of a healthy male volunteer. The L4-L5 intervertebral space was selected as the surgical segment. The surgical models were established separately based on OLIF surgical procedures and different internal fixations: 1) stand-alone OLIF (SA); 2) OLIF with a 2-screw lateral plate; 3) OLIF with a 4-screw lateral plate; 4) OLIF with OLLPS; and 5) OLIF with bilateral pedicle screw fixation (BPS). After validation of the intact model, physiologic loads were applied to the superior surface of L1 to simulate motions such as flexion, extension, left bending, right bending, left rotation, and right rotation. The evaluation indices included the L4/5 range of motion, the L4 maximum displacement, and the maximum stresses of the superior and inferior end plates, the cage, and the supplemental fixation. Results: During OLIF surgery, the OLLPS provided multiplanar stability similar to that provided by BPS. Compared with 2-screw lateral plate and 4-screw lateral plate, OLLPS had better biomechanical properties in terms of enhancing the instant stability of the surgical segment, reducing the stress on the superior and inferior end plates of the surgical segment, and decreasing the risk of cage subsidence. Conclusions: With a minimally invasive background, the OLLPS can be used as an alternative to BPS in OLIF and it has better prospects for clinical promotions and applications.
Biomechanical changes of oblique lumbar interbody fusion with different fixation techniques in degenerative spondylolisthesis lumbar spine: a finite element analysis

Er-Xu Tao,Ren-Jie Zhang,Bo Zhang,Jia-Qi Wang,Lu-Ping Zhou,Cai-Liang Shen

DOI: https://doi.org/10.1186/s12891-024-07796-1

IF: 2.562

2024-08-27

BMC Musculoskeletal Disorders

Abstract:There is a dearth of comprehensive research on the stability of the spinal biomechanical structure when combining Oblique Lumbar Interbody Fusion (OLIF) with internal fixation methods. Hence, we have devised this experiment to meticulously examine and analyze the biomechanical changes that arise from combining OLIF surgery with different internal fixation techniques in patients diagnosed with degenerative lumbar spondylolisthesis.

orthopedics,rheumatology
Purification and properties of cytochrome c555 from Leishmania donovani.

M. Rassam,N. Dawood

DOI: https://doi.org/10.1016/0166-6851(86)90072-1

1986-10-01

Abstract:
The effect of different fixation systems on oblique lumbar interbody fusion under vibration conditions

Bin Zhang,Tian-Cheng Li,Xin Wang,Cheng-Fei Du,Rui Zhu

DOI: https://doi.org/10.1016/j.medengphy.2024.104169

IF: 2.356

2024-04-18

Medical Engineering & Physics

Abstract:Despite the fact that lower back pain caused by degenerative lumbar spine pathologies seriously affects the quality of life, however, there is a paucity of research on the biomechanical properties of different auxiliary fixation systems for its primary treatment (oblique lumbar interbody fusion) under vibratory environments. In order to study the effects of different fixation systems of OLIF surgery on the vibration characteristics of the human lumbar spine under whole-body vibration (WBV), a finite element (FE) model of OLIF surgery with five different fixation systems was established by modifying a previously established model of the normal lumbar spine (L1-S1). In this study, a compressive follower load of 500 N and a sinusoidal axial vertical load of ±40 N at the frequency of 5 Hz with a duration of 0.6s was applied. The results showed that the bilateral pedicle screw fixation model had the highest resistance to cage subsidence and maintenance of disc height under WBV. In contrast, the lateral plate fixation model exerted very high stresses on important tissues, which would be detrimental to the patient's late recovery and reduction of complications. Therefore, this study suggests that drivers and related practitioners who are often in vibrating environments should have bilateral pedicle screws for OLIF surgery, and side plates are not recommended to be used as a separate immobilization system. Additionally, the lateral plate is not recommended to be used as a separate fixation system.

engineering, biomedical
Biomechanical Assessment of Different Transforaminal Lumbar Interbody Fusion Constructs in Normal and Osteoporotic Condition-A Finite Element Analysis

Chen Liu,Mengmeng Zhao,Wencan Zhang,Chongyi Wang,Bingtao Hu,Kaibin Wang,Wanlong Xu,Le Li,Haipeng Si

DOI: https://doi.org/10.1016/j.spinee.2024.01.017

IF: 4.297

2024-02-05

The Spine Journal

Abstract:BACKGROUND CONTEXT : With the aging population, osteoporosis, which leads to poor fusion, has become a common challenge for lumbar surgery. In addition, most people with osteoporosis are elderly individuals with poor surgical tolerance, and poor bone quality can also weaken the stability of internal fixation. PURPOSE : This study compared the fixation strength of the bilateral traditional trajectory screw structure (TT-TT), the bilateral cortical bone trajectory screw structure (CBT-CBT), and the hybrid CBT-TT (CBT screws at the cranial level and TT screws at the caudal level) structure under different bone mineral density conditions. STUDY DESIGN : A finite element (FE) analysis study. METHODS Above all, we established a healthy adult lumbar spine model. Second, under normal and osteoporotic conditions, three transforaminal lumbar interbody fusion (TLIF) models were established: bilateral traditional trajectory (TT-TT) screw fixation, bilateral cortical bone trajectory (CBT-CBT) screw fixation, and hybrid cortical bone trajectory screw and traditional trajectory screw (CBT-TT) fixation. Finally, a 500-N compression load with a torque of 10 N/m was applied to simulate flexion, extension, lateral bending, and axial rotation. We compared the range of motion (ROM), adjacent disc stress, cage stress, and posterior fixation stress of the different fusion models. RESULTS : Under different bone mineral density conditions, the range of motion of the fusion segment was significantly reduced. Compared to normal bone conditions, the ROM of the L4-L5 segment, the stress of the adjacent intervertebral disc, the surface stress of the cage, and the maximum stress of the posterior fixation system were all increased in osteoporosis. Under most loads, the ROM and surface stress of the cage and the maximum stress of the posterior fixation system of the TT-TT structure are the lowest under normal bone mineral density conditions. However, under osteoporotic conditions, the fixation strength of the CBT-CBT and CBT-TT structures are higher than that of the TT-TT structures under certain load conditions. At the same time, the surface stress of the intervertebral fusion cage and the maximum stress of the posterior fixation system for the two structures are lower than those of the TT-TT structure. CONCLUSION : Under normal bone mineral density conditions, transforaminal lumbar interbody fusion combined with TT-TT fixation provides the best biomechanictability. However, under osteoporotic conditions, CBT-CBT and CBT-TT structures have higher fixed strength compared to TT-TT structures. The hybrid CBT-TT structure exhibits advantages in minimal trauma and fixation strength. Therefore, this seems to be an alternative fixation method for patients with osteoporosis and degenerative spinal diseases. CLINICAL SIGNIFICANCE This study provides biomechanical support for the clinical application of hybrid CBT-TT structure for osteoporotic patients undergoing TLIF surgery.

clinical neurology,orthopedics
Complications and Prevention Strategies of Oblique Lateral Interbody Fusion Technique.

Zhong-You Zeng,Zhao-Wan Xu,Deng-Wei He,Xing Zhao,Wei-Hu Ma,Wen-Fei Ni,Yong-Xing Song,Jian-Qiao Zhang,Wei Yu,Xiang-Qian Fang,Zhi-Jie Zhou,Nan-Jian Xu,Wen-Jian Huang,Zhi-Chao Hu,Ai-Lian Wu,Jian-Fei Ji,Jian-Fu Han,Shun-Wu Fan,Feng-Dong Zhao,Hui Jin,Fei Pei,Shi-Yang Fan,De-Xiu Sui

DOI: https://doi.org/10.1111/os.12380

2018-01-01

Orthopaedic Surgery

Abstract:Objective: To analyze the early complications and causes of oblique lateral interbody fusion, and put forward preventive measures. Methods: There were 235 patients (79 males and 156 females) analyzed in our study from October 2014 to May 2017. The average age was 61.9 +/- 0.21 years (from 32 to 83 years). Ninety-one cases were treated with oblique lateral interbody fusion (OLIF) alone (OLIF alone group) and 144 with OLIF combined with posterior pedicle screw fixation through the intermuscular space approach (OLIF combined group). In addition, 137/144 cases in the combined group were primarily treated by posterior pedicle screw fixation, while the treatments were postponed in 7 cases. There were 190 cases of single fusion segments, 11 of 2 segments, 21 of 3 segments, and 13 of 4 segments. Intraoperative and postoperative complications were observed. Results: Average follow-up time was 15.6 +/- 7.5 months (ranged from 6 to 36 months). Five cases were lost to follow-up (2 cases from the OLIF alone group and 3 cases from the OLIF combined group). There were 7 cases of vascular injury, 22 cases of endplate damage, 2 cases of vertebral body fracture, 11 cases of nerve injury, 18 cases of cage sedimentation or cage transverse shifting, 3 cases of iliac crest pain, 1 case of right psoas major hematoma, 2 cases of incomplete ileus, 1 case of acute heart failure, 1 case of cerebral infarction, 3 case of left lower abdominal pain, 9 cases of transient psoas weakness, 3 cases of transient quadriceps weakness, and 8 cases of reoperation. The complication incidence was 32.34%. Thirty-three cases occurred in the OLIF alone group, with a rate of 36.26%, and 43 cases in the group of OLIF combined posterior pedicle screw fixation, with a rate of 29.86%. Fifty-seven cases occurred in single-segment fusion, with a rate of 30.0% (57/190), 4 cases occurred in two-segment fusion, with a rate of 36.36% (4/11), 9 cases occurred in three-segment fusion, with a rate of 42.86% (9/21), and 6 cases occurred in four-segment fusion, with a rate of 46.15% (6/13). Conclusion: In summary, OLIF is a relatively safe and very effective technique for minimally invasive lumbar fusion. Nonetheless, it should be noted that OLIF carries the risk of complications, especially in the early stage of development.
[Oblique Lumbar Interbody Fusion Combined With 4-Screw Fixation for Treating Two-Level Degenerative Lumbar Diseases:A Finite Element Study]

Ting Ge,Bai-Wen Hu,Jin Xiao,Qiao-Lin Zhang,Xiao-Chuan Wu,Dong-Dong Xia

DOI: https://doi.org/10.3881/j.issn.1000-503X.15878

Abstract:Objective To demonstrate the feasibility of oblique lumbar interbody fusion (OLIF) combined with 4-screw fixation for treating two-level lumbar degenerative diseases.Methods An intact finite element model of L3-S1 (M0) was constructed and validated.Then,we constructed the M1 model by simulating OLIF surgery at L3/4 and L4/5 segments on the M0 model.By attachment of posterior 4-screw or 6-screw fixation to the M1 model,three 4-screw fixation models (M2-M4) and one 6-screw fixation model (M5) were established.The segmental and overall range of motion (ROM) and the peak von Mises stresses of superior endplate,cage,and posterior screw-rod were investigated under each implanted condition.Results Under the motion modes of forward flexion,backward extension,bilateral (left and right) flexion,and left and right rotation,the L3/4 ROM of M2 model and L4/5 ROM of M3 model increased,while the L3/4 and L4/5 ROM of M4 and M5 models significantly decreased compared with those of M1 model.Under all motion modes,the L4 superior endplate in M2 model and the L5 superior endplate in M3 model showed the maximum peak von Mises stress,and the peak von Mises stresses of L4 and L5 superior endplates in M4 and M5 models were close.The L3/4 cage in M2 model and the L4/5 cage in M3 model showcased the largest peak von Mises stress,and the peak von Mises stresses of cages in M4 and M5 models were close.The peak stresses of internal fixation in M2-M5 models were close.Conclusion Four-screw fixation can replace 6-screw fixation in the OLIF surgery for treating two-level degenerative lumbar diseases.
The effect of polymethylmethacrylate augmentation on the primary stability of stand-alone implant construct versus posterior stabilization in oblique lumbar interbody fusion with osteoporotic bone quality– a finite element study

Ferenc Bereczki,Mate Turbucz,Agoston Jakab Pokorni,Benjamin Hajnal,Marton Rónai,Istvan Klemencsics,Aron Lazary,Peter Endre Eltes

DOI: https://doi.org/10.1016/j.spinee.2024.01.021

IF: 4.297

2024-02-03

The Spine Journal

Abstract:Background Context Oblique lumbar interbody fusion (OLIF) can provide an ideal minimally invasive solution for achieving spinal fusion in an older, more frail population where decreased bone quality can be a limiting factor. Stabilization can be achieved with bilateral pedicle screws (BPS), which require additional incisions and longer operative time. Alternatively, a novel self-anchoring stand-alone lateral plate system (SSA) can be used, where no additional incisions are required. Based on the relevant literature, BPS constructs provide greater primary biomechanical stability compared to lateral plate constructs, including SSA. This difference is further increased by osteoporosis. Screw augmentation in spinal fusion surgeries is commonly used; however, in the case of OLIF, it is a fairly new concept, lacking a consensus-based guideline. Purpose This comparative study aimed to investigate the effect of PMMA screw augmentation on the primary stability of a stand-alone implant construct versus posterior stabilization in oblique lumbar interbody fusion with osteoporotic bone quality. Study Design The biomechanical effect of screw augmentation was studied inside an in-silico environment using computer-aided finite element analysis. Methods A previously validated and published L2-L4 finite element model with normal and osteoporotic bone material properties was used. Geometries based on the OLIF implants (BPS, SSA) were created and placed inside the L3-L4 motion segment with increasing volumes (1 cm3 – 6 cm3) of PMMA augmentation. A 400 N follower load and 10 Nm bending moment (in the three anatomical planes) were applied to the surgical finite element models with different bone material properties. The operated L3-L4 segmental range of motion (ROM), the inserted cage's maximal caudal displacements, and L4 cranial bony endplate principal stress values were measured. Results The non-augmented values for the BPS construct were generally lower compared to SSA, and the difference was increased by osteoporosis. In osteoporotic bone, PMMA augmentation gradually decreased the investigated values and the difference between the two constructs as well. Between 3 cm 3 and 4 cm 3 of injected PMMA volume per screw, the difference between augmented SSA and standard BPS became comparable. Conclusions Based on this study, augmentation can enhance the primary stability of the constructs and decrease the difference between them. Considering leakage as a possible complication, between 3 cm 3 and 4 cm 3 of injected PMMA per screw can be an adequate amount for SSA augmentation. However, further in silico, and possibly in vitro and clinical testing is required to thoroughly understand the investigated biomechanical aspects. Clinical Significance This study sheds light on the possible biomechanical advantage offered by augmented OLIF implants and provides a theoretical augmentation amount for the SSA construct. Based on the findings, the concept of an SSA device with PMMA augmentation capability is desirable.

clinical neurology,orthopedics
Biomechanical study of two-level oblique lumbar interbody fusion with different types of lateral instrumentation: a finite element analysis

Yuan Zhong,Yujie Wang,Hong Zhou,Yudong Wang,Ziying Gan,Yimeng Qu,Runjia Hua,Zhaowei Chen,Genglei Chu,Yijie Liu,Weimin Jiang

DOI: https://doi.org/10.3389/fmed.2023.1183683

IF: 3.9

2023-06-23

Frontiers in Medicine

Abstract:Objective The aim of this study was to verify the biomechanical properties of a newly designed angulated lateral plate (mini-LP) suited for two-level oblique lumbar interbody fusion (OLIF). The mini-LP is placed through the lateral ante-psoas surgical corridor, which reduces the operative time and complications associated with prolonged anesthesia and placement in the prone position. Methods A three-dimensional nonlinear finite element (FE) model of an intact L1–L5 lumbar spine was constructed and validated. The intact model was modified to generate a two-level OLIF surgery model augmented with three types of lateral fixation (stand-alone, SA; lateral rod screw, LRS; miniature lateral plate, mini-LP); the operative segments were L2–L3 and L3–L4. By applying a 500 N follower load and 7.5 Nm directional moment (flexion-extension, lateral bending, and axial rotation), all models were used to simulate human spine movement. Then, we extracted the range of motion (ROM), peak contact force of the bony endplate (PCFBE), peak equivalent stress of the cage (PESC), peak equivalent stress of fixation (PESF), and stress contour plots. Results When compared with the intact model, the SA model achieved the least reduction in ROM to surgical segments in all motions. The ROM of the mini-LP model was slightly smaller than that of the LRS model. There were no significant differences in surgical segments (L1–L2, L4–L5) between all surgical models and the intact model. The PCFBE and PESC of the LRS and the mini-LP fixation models were lower than those of the SA model. However, the differences in PCFBE or PESC between the LRS- and mini-LP-based models were not significant. The fixation stress of the LRS- and mini-LP-based models was significantly lower than the yield strength under all loading conditions. In addition, the variances in the PESF in the LRS- and mini-LP-based models were not obvious. Conclusion Our biomechanical FE analysis indicated that LRS or mini-LP fixation can both provide adequate biomechanical stability for two-level OLIF through a single incision. The newly designed mini-LP model seemed to be superior in installation convenience, and equally good outcomes were achieved with both LRS and mini-LP for two-level OLIF.

medicine, general & internal
Biomechanical evaluation of different oblique lumbar interbody fusion constructs: a finite element analysis

Zhengquan Xu,Qingcong Zheng,Liqun Zhang,Rongsheng Chen,Zhechen Li,Weihong Xu

DOI: https://doi.org/10.1186/s12891-024-07204-8

IF: 2.562

2024-01-28

BMC Musculoskeletal Disorders

Abstract:Finite element analysis (FEA) was performed to investigate the biomechanical differences between different adjunct fixation methods for oblique lumbar interbody fusion (OLIF) and to further analyze its effect on adjacent segmental degeneration.

orthopedics,rheumatology
Early Complications Associated with Oblique Lateral Interbody Fusion in the Treatment of Degenerative Lumbar Diseases

Wang Jiying,Zhou Zhijie,Fan Shunwu,Fang Xiangqian,Zhao Fengdong,Zhang Jianfeng,Zhao Xing,Hu Zhijun,Liu Junhui,Wang Yanyan

DOI: https://doi.org/10.3760/cma.j.issn.0253-2352.2017.16.007

2017-01-01

Abstract:Objective To evaluate the early clinical outcomes and complications of oblique lateral interbody fusion (OLIF) in the treatment of degenerative lumbar diseases.Methods All of 83 patients,29 males and 54 females with ages from 32 to 83 (average 60.8± 13.7 y),underwent OLIF with or without posterior pedicle screw-rod instrumentations from October 2014 to February 2017.The index diagnosis was discogenic back pain in 17 cases,spondylolisthesis in 23,lumbar spinal canal stenosis in 25,and degenerative lumbar spinal kyphoscoliosis in 18 cases.The distribution of operative level was 5 at L1,2,13 at L2,3,38 at L3,4,and 69 at L4,5.The mean number of fusion level for each case was 1.5 segments.The operative duration,blood loss during operation,intra-operative and post-operative complications,the length of post-operative hospital stay were recorded.Clinical outcomes were evaluated using visual analogue scale (VAS) and Oswestry disability index (ODI).All patients were followed up for at least 3 months.Lumbar X-ray and CT scans were taken and the clinical outcomes were re-assessed during follow-up.Results Fifty-one in the 83 patients underwent supplementary posterior pedicle screw-rod instrumentation with OLIF procedures.The operation lasted for 43-295 min,with a mean duration of (153 ± 72) min.Mean operation time for each OLIF segment was 43± 12 min.Blood loss during the operation was 30-800 ml,with a mean of 125±74 ml.Mean blood loss for each OLIF segment was 27±13 min.Average length of stay was 5.6 ± 3.2 d,ranging from 3-15 d.The VAS for back pain and leg pain and ODI scores were decreased apparently for each patient.The total incidence of complications was 22.9％ (19/83),including 6.0％ (5/83) of intra-operative complications (4 cases of cage subsidence,1 case of segmental artery injury) and 16.9％ (14/83) of post-operative ones.The latter consisted of ipsilateral hip flexor weakness in 6,ipsilateral anterolateral thigh pain in 2,ipsilateral lateral thigh numbness in 1,contralateral pain in flexion of hip in 1,ipsilateral sympathetic chain injury in 2,and pain in area of iliac bone donor site in 2.All symptoms were released or disappeared during follow-up.Conclusion OLIF as a novel minimally invasive technique can act as a safe and effective treatment for degenerative lumbar diseases,which can also reduce approach-related complications.

[ECG before administration of Ritalin®: Is it useful ?]

The biomechanical study of a modified lumbar interbody fusion-crenel lateral interbody fusion (CLIF): a three-dimensional finite-element analysis.

Biomechanical study of oblique lumbar interbody fusion (OLIF) augmented with different types of instrumentation: a finite element analysis

Oblique Lateral Interbody Fusion Combined With Lateral Plate Fixation for the Treatment of Lumbar Degenerative Diseases: a Preliminary Clinical Study

Oblique Lateral Interbody Fusion Combined With Different Internal Fixations in The Treatment of Degenerative Lumbar Spine Disease: A Finite Element Analysis

Oblique lateral interbody fusion combined with different internal fixations for the treatment of degenerative lumbar spine disease: a finite element analysis

Biomechanical stability of oblique lateral interbody fusion combined with four types of internal fixations: finite element analysis

Biomechanical Evaluation of Anterolateral Screw Fixation for Oblique Lumbar Interbody Fusion Surgery – A Finite Element Analysis

An in vitro biomechanical evaluation of integrated lateral plate combined with oblique lateral interbody fusion in different bone conditions

Stability Evaluation of Different Oblique Lumbar Interbody Fusion Constructs in Normal and Osteoporotic Condition – A Finite Element Based Study

Biomechanical Evaluation of an Oblique Lateral Locking Plate System for Oblique Lumbar Interbody Fusion: A Finite Element Analysis

Biomechanical changes of oblique lumbar interbody fusion with different fixation techniques in degenerative spondylolisthesis lumbar spine: a finite element analysis

Purification and properties of cytochrome c555 from Leishmania donovani.

The effect of different fixation systems on oblique lumbar interbody fusion under vibration conditions

Biomechanical Assessment of Different Transforaminal Lumbar Interbody Fusion Constructs in Normal and Osteoporotic Condition-A Finite Element Analysis

Complications and Prevention Strategies of Oblique Lateral Interbody Fusion Technique.

[Oblique Lumbar Interbody Fusion Combined With 4-Screw Fixation for Treating Two-Level Degenerative Lumbar Diseases:A Finite Element Study]

The effect of polymethylmethacrylate augmentation on the primary stability of stand-alone implant construct versus posterior stabilization in oblique lumbar interbody fusion with osteoporotic bone quality– a finite element study

Biomechanical study of two-level oblique lumbar interbody fusion with different types of lateral instrumentation: a finite element analysis

Biomechanical evaluation of different oblique lumbar interbody fusion constructs: a finite element analysis

Early Complications Associated with Oblique Lateral Interbody Fusion in the Treatment of Degenerative Lumbar Diseases